📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP Grating in a Hydrocarbon Fire

Fire performance
Direct Answer

FRP grating survives hydrocarbon pool fires as a drainage and access deck, but it is not a fire barrier: phenolic grades with low smoke are the specification, and structural protection stays with the steel frame.

  • Best for: offshore drainage decks, bunded areas, escape routes
  • Not for: replacing passive fire protection on primary structure
  • Key spec: phenolic, Class 1 low smoke, marine approvals named per project, sealed edges

A hydrocarbon fire is not a bigger version of the flame spread test. It is a different exposure, with a different failure mode, and specifying a deck for it means knowing which test the number on the datasheet came from.

Does FRP Grating Survive a Hydrocarbon Fire?

FRP grating survives hydrocarbon pool fires as a drainage and access deck, but it is not a fire barrier: phenolic grades with low smoke are the specification, and structural protection stays with the steel frame. A hydrocarbon fire is not a bigger version of the flame spread test. It is a different exposure, with a different failure mode, and specifying a deck for it means knowing which test the number on the datasheet came from.

The honest answer is that the deck keeps walking and drainage access through a short, localised fire so that an escape route or a bunded area remains usable; it does not hold back the fire, and it must never be specified as passive fire protection on the primary structure. The resin of every component in the load path, not just the panel, is what decides whether the system holds. A buyer who only reads the panel class is buying half a system, and the other half fails on the first real exposure.

ABS product design assessment certificate for FRP grating

Four Hydrocarbon Scenarios and How the Deck Responds

Almost every FRP grating datasheet quotes a surface burning class, usually ASTM E-84 Class A or Class B, or the European equivalent EN 13501-1. That test measures flame spread along a horizontal specimen in a tunnel under a modest exposure. It tells you how the material behaves when a fire is next to it. A hydrocarbon fire is a pool fire or a jet fire: a large heat flux, a fast temperature rise, and a flame that engulfs the member from below. The two are measured on different curves and they produce different failures. A Class B panel and a hydrocarbon-rated system are not the same claim, and a supplier who answers a hydrocarbon question with a flame spread class has answered a different question.

The table below separates the four scenarios a marine or process engineer actually faces. Read the third column together with the fourth: the FRP response tells you what the panel does, and the recommended specification tells you what the system needs around it. None of the four rows is a licence to omit passive protection on the steel frame; the grating is the walking surface, not the firewall.

ScenarioExposureFRP responseRecommended specification
Pool fireRadiant heat, 30-60 minSurface char, resin lossPhenolic, protected supports
Jet fireHigh heat flux, short durationLocalised burn-through riskPhenolic plus passive protection
Confined moduleHot gas and smokeSmoke-driven failure firstLow-smoke phenolic, Class 1
Drainage deckFlammable liquid spillGrating survives, drainage mattersPhenolic, sealed edges

Why Phenolic Is the Only Grade That Belongs Here

Phenolic resin is the grade that matters in fire, and it matters for two reasons. It chars rather than burns, forming a carbon layer that insulates the material behind it, and it produces very little smoke and very little toxic gas compared with polyester or vinyl ester. The char layer is the mechanism: as heat attacks the surface, the resin pyrolyses into a stable carbon skin that slows heat transfer into the glass, which is why a phenolic panel keeps its geometry long after a polyester panel has slumped.

Smoke is the reason phenolic is specified more often than flame spread. In an enclosed space, a deck that keeps its structural integrity while filling the room with dense smoke is still a deck nobody escapes across. Phenolic keeps the escape route visible for longer, which is why it appears in offshore modules, tunnels, rail and enclosed plant rooms rather than in open yards. Vinyl ester remains the right choice for chemical service where no fire class is required, but it is not a substitute where smoke and toxicity drive the specification.

Where the Deck Is the Weak Link

A grating deck is an open mesh, which changes the fire problem in two ways. The open area lets heat and flame pass through, so the underside of the walking surface is exposed directly rather than shielded; and the deck has very little mass, so it heats quickly. There is no thick section to act as a heat sink, and no solid soffit to deflect a flame jet. That is why the open mesh survives a drainage deck fire but fails a jet fire unless the steel beneath is passively protected.

What usually fails first is not the panel but the system around it: the clips and bolts that hold the panel, the bearer that softens under load, and the handrail that loses its base. A deck specified as phenolic panels on polyester bearers, fixed with ordinary clips, has one fire-rated component and three that are not. The specification therefore has to name the resin of panel, bearer, clip, handrail and base plate together, rather than treating the panel as the only fire-rated item.

What a Hydrocarbon Specification Should State

A complete hydrocarbon specification is a short list, and every line prevents a later argument:

  • The design fire: pool fire or jet fire, the heat flux, and the duration the deck has to survive.
  • Whether the requirement is integrity only, or integrity plus insulation, and for how long.
  • The test standard and the classification claimed, named exactly, with the report referenced.
  • The resin of every component in the load path, not just the panel: panel, bearer, clip, handrail, base plate.
  • The smoke and toxicity requirement for the space the deck serves.
  • Whether a coating, a soffit board or a filled deck is part of the system, because those are often what delivers the rating.

We hold an Intertek test report to ASTM F3059, which is the marine FRP grating specification and covers fire performance among other properties, and we can send it on request with the certificate pack. We can quote phenolic grating and phenolic profiles, and we can state the resin of every component. Where a specific ABS or DNV approval is contractually required, we will name the approval status on the project rather than imply one that has expired.

Installation and System Checks That Protect the Rating

Because the deck is open mesh, the installation details carry the rating as much as the resin does. Cut edges and drilled holes must be sealed with matching phenolic resin before handover; an unsealed edge lets heat and flame attack the exposed glass directly and shortens the char layer. Clips should be stainless and sized for the span, and the clip layout should be checked against the uplift case as well as the dead load, because a jet fire generates a pressure pulse that can lift a poorly fixed panel. On a drainage deck, keep the open area clear so flammable liquid passes through rather than pooling on the walking surface.

Bearers should be phenolic profiles, or steel profiles with passive protection, and the handrail base plates should be fixed through a bearing plate rather than into the panel alone. On site, keep the approved phenolic sample panel so the installer can compare colour, grit and bar geometry before the first bundle is fixed. Walk the deck before it is sealed: a cured phenolic panel feels hard and does not smell of styrene, and any soft or tacky patch is rejected before it reaches the installation. Record the sealant batch on the handover list, because a mismatched edge seal is the most common reason a phenolic deck fails its first site audit.

Cost, Lead Time and What We Will Not Quote

Phenolic grating costs more than standard polyester, and the premium is justified on offshore and bunded decks where the specification actually calls for low smoke; it is not justified on open, ventilated walkways where no escape-route visibility requirement exists. Compare the landed cost and the 20-year maintenance line, not the unit price, and ask every supplier for a landed-cost table. Because phenolic panels are bulky, freight is volume-driven, and a part container can look disproportionately expensive per square metre.

What we will not do is describe a general purpose or isophthalic panel as hydrocarbon resistant because it passed a surface flame spread test. Where the design case is a hydrocarbon fire, the honest answer is a system specification with the test evidence named, and if that evidence does not exist for a component, the specification says so. We manufacture at a 20,000 m2+ plant with 200+ staff, export to 40+ countries, hold MOQ 10 m2 and a 12-36 working day lead time from a confirmed drawing, so a phenolic package can be staged alongside the steel structure rather than after it. Oversized panels, custom colours, new moulds and specialty resins are quoted with a separately confirmed schedule.

Frequently Asked Questions

Is FRP grating suitable for a hydrocarbon fire?
Only as a specified system, with the design fire defined and the test evidence named for every component. A general purpose panel is not. Expect a phenolic deck on protected supports, with the resin named for panel, bearer, clips and handrail.
Does ASTM E-84 Class B mean hydrocarbon rated?
No. E-84 measures surface flame spread in a tunnel test under a modest exposure. A hydrocarbon fire is a pool or jet fire with a large heat flux, a fast temperature rise and a different failure mode, and the two are not interchangeable.
Why is phenolic used instead of vinyl ester in fire?
Phenolic chars and produces very little smoke. Smoke, not flame spread, is usually what decides whether an escape route stays usable in an enclosed module, and a phenolic panel keeps visibility for 30-60 minutes longer than vinyl ester.
Will the panel or the clips fail first?
Usually the fixings and the bearers. The panel is one component; the load path through clips, bearers and base plates decides whether the deck stays put. A jet fire pressure pulse can lift a panel that was fixed for dead load only.
Can you supply phenolic profiles as well as phenolic grating?
Yes, and where the design case is fire the bearers should be phenolic too, otherwise the system has one rated component and three unrated ones. We state the resin of every component in the load path on the drawing.
Can I see the fire test report?
Yes. The Intertek ASTM F3059 report is sent with the certificate pack on request, along with the ISO 9001 certificate 01708Q11888R0S. Where a specific ABS or DNV approval is required, we name its current status on the project.
ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026-09-09 |Category: Fire performance|Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating Fire Ratings Explained

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]