The grating resin families split by duty level, cost and indicative wet envelope: ortho near 60 °C, iso near 80 °C, vinyl ester near 100 °C, epoxy near 120 °C and phenolic near 150 °C in its fire-rated placement. These figures are preliminary selection guides from the resin guide, not guaranteed service limits. Hot, concentrated or critical exposure requires a written compatibility confirmation before ordering.
- Family ladder: ortho (dry/mild) → iso (aqueous/humid) → VE (acid/bleach/caustic) → epoxy (special aggressive/heat) → phenolic (fire-related areas).
- Wet envelopes are selection ranges at the reference basis; ratings drop one step at higher heat or concentration.
- No family covers an unlisted medium by analogy; critical, hot or concentrated duty waits on written review.
1. The family ladder at a glance
Each grating resin pairs glass roving with a different matrix. The roving supplies stiffness in every family; the polymer decides which moisture, acid, alkali or solvent the panel can meet. Moving up the ladder buys a more resistant matrix at higher cost, and the family should follow the documented medium rather than a precautionary upgrade.
The resin guide quotes indicative wet envelopes to position each family. These ranges help preliminary sizing; they do not set a guaranteed service temperature, and a panel near its upper envelope needs factory confirmation against the grade.
| Resin family | Cost | Indicative wet limit | Best for | Outside its best scope |
|---|---|---|---|---|
| Orthophthalic polyester | Lowest | ~60 °C | Fresh water, mild alkali, general use | Strong acid, solvents |
| Isophthalic polyester | Mid | ~80 °C | Wastewater, seawater, mild acid, moist air | Strong oxidisers, hot solvents |
| Vinyl ester | Higher | ~100 °C | Strong acid, bleach, caustic, scrubbers | Some ketones, high aromatics |
| Epoxy | Highest | ~120 °C | Special structural, aggressive chemical, heat | Cost-sensitive general walkways |
| Phenolic | On request | ~150 °C, fire-rated | Offshore, tunnel, public fire-related areas | Continuous strong alkali |
Wet limits are family selection guides; confirm critical, hot or concentrated exposure in writing before the resin grade is locked.
2. How cost and duty line up
The lowest-cost ortho suits the gentlest environment, and spending up the ladder should track real chemical demand. An iso or VE placed on a dry general deck overpays for duty ortho already meets; equally, an aggressive acid platform left on iso under-specifies the matrix.
Epoxy and phenolic sit outside the ordinary cost walkway: epoxy for special structural and highly aggressive service, phenolic for a fire-related area requirement. Neither belongs on a routine deck on assumption alone; both need project-specific evidence.
3. Limits the comparison does not settle
A recurring counter-example is selecting the cheapest family for an aggressive duty and reading the wet-limit figure as a promise of survival. The envelope is a preliminary range; concentrated liquor, hot residue or continuous immersion can push a panel past it, and the listed rating drops one step above the band. Hot duty must be confirmed against the actual grade rather than inferred from the family table.
The comparison also does not rank resistance to an unlisted solvent, oxidiser or mixed stream. A medium absent from the reference chart cannot be assigned a family grade by analogy with a listed one; that case goes to a compatibility test or engineering review. Fire performance, food contact and drinking-water approval are separate evidence questions this family table does not answer.
| Misread | What it overlooks | Correct treatment |
|---|---|---|
| Cheapest resin for aggressive duty | Matrix tolerance follows the medium, not the budget | Match family to documented chemistry |
| Wet limit as a service guarantee | Figure is a selection range; heat/concentration downgrades | Confirm hot duty against the grade in writing |
| Unlisted medium rated by analogy | No listed row supports the grade | Test or engineering compatibility review |
| Fire/contact claim from resin name | Requires matched separate evidence | Verify destination regulation and document |
Indicative wet ranges are preliminary; hot, concentrated or critical exposure requires a written compatibility confirmation before ordering.
4. Confirming the family before specification
Before locking a family, record the medium, concentration band, thermal band and contact mode, and mark any critical or immersion duty separately. Check the location for adjacent acid, solvent or steam exposure that could raise the condition after installation; those hazards belong in the specification brief.
On delivery, inspect resin face and edge seal for each family used. The missing evidence — grade-specific maximum wet and dry temperature, plus any thermal cycling or prolonged heat exposure — must close with the factory or engineering review before the walkway is released.
5. Frequently Asked Questions
Which resin suits all resin families exposure on FRP grating?
No resin family is confirmed for all resin families from the published basis. The medium is unlisted, so an A/B/C grade cannot be assigned; a documented compatibility check or test covering comparison of wet service envelopes across families precedes specification. Indicative wet ranges are preliminary; hot, concentrated or critical exposure requires a written compatibility confirmation before ordering.
Is all resin families covered by the reference compatibility chart?
No. all resin families is absent from the reference compatibility listing. Treat the service as test-required and close the missing evidence by factory or engineering review before ordering.
Does this resin choice certify food-safe or drinking-water use?
No. Food-contact and drinking-water compliance are not established from the resistance chart. Where the project requires such approval, obtain the matched compliance document and verify it against the destination regulation before ordering.
What changes the resistance rating besides the resin family?
Concentration, heat and contact type all move the rating. At higher temperature or concentration the grade drops one step; immersion is stricter than splash or intermittent wetting.
What must be confirmed before an order for this service?
Provide the exact medium, min/max concentration, min/max temperature and contact type. Critical, hot, concentrated or unlisted exposure needs a written factory confirmation or project-specific test; combined duty stays on technical review.
Reference PDFs: resin-selection-guide.pdf · frp-grp-grating-technical-data-sheet.pdf
