/>

Bending Versus Shear in Choosing Grating Bar Depth

Structural Mechanics
Direct Answer

A loaded bar resists both bending along its span and shear near its supports; the span-to-depth relationship usually decides which of the two demands sets the section depth.

  • Separate the bending moment from the shear force acting on each bar.
  • Apply the simply supported beam formulas to the preliminary demand check.
  • Long spans tend toward bending and deflection; short deep spans need a shear check.

1. Bending and Shear Are Two Demands on the Bar

When a panel carries load, each spanning bar acts like a small beam. Bending tries to curve the bar between supports, producing tensile and compressive stress across its depth; shear tries to slide one part of the bar past another, mainly close to the support. Both demands must be within what the section and material can carry.

Choosing bar depth is often framed around stiffness and span, but the section should also be checked for shear. A shallow bar over a long span is dominated by bending and sag; a deep, short bar may reach its shear limit before bending becomes the controlling condition.

  • bending moment. the internal couple that curves a bar between supports, giving tension and compression across the depth.
  • shear force. the internal force that tends to slide adjacent sections of the bar past one another.
  • span-to-depth ratio. the support span divided by the bar depth, a guide to whether bending or shear tends to govern.
  • bar depth. the vertical height of a load-carrying bar in the panel.
  • demand. the bending or shear force placed on the section by the applied load.

2. Beam Formulas for a Simply Supported Panel

For a simply supported panel carrying a uniform load q per unit area, treat a strip of known width as a beam with line load w. The maximum bending moment is M_max = wL²/8, and the maximum shear force is V_max = wL/2, at the supports. For a central point load P, the moment is PL/4 and the shear is P/2.

Bending stress relates to the section through σ = M·c/I, where c is the distance to the extreme fiber and I the second moment of area; shear stress relates to the bar web area through τ = V/(d·t_w). These expressions frame a preliminary check; permissible stresses and deflection limits follow the datasheet and the adopted design standard.

Load caseMaximum momentMaximum shear
Uniform load, simply supportedM = wL²/8V = wL/2
Central point loadM = PL/4V = P/2
Strip modelPer-bar tributary width appliedPer-bar tributary width applied

3. Which Demand Usually Governs by Span

As the span grows, the bending moment rises with the square of the length, while shear rises only linearly. Long-span bars therefore usually fail or deflect in bending first, and depth is added mainly to control sag and bending stress. Over a short span, the bar is deeper relative to its length and the shear check at the support becomes the more likely limit.

The balance also depends on the bar profile. I-bar, T-bar and molded sections distribute material differently, so bending stiffness and shear area are not interchangeable between families. The section comparison should use the datasheet values for the chosen profile rather than depth alone.

  • Read the span and the applied load before comparing bending and shear demand.
  • Check the short deep section for shear even when bending looks comfortable.
  • Match the bar family to the governing demand, not depth alone.

4. Worked Comparison: Demand vs Section

As an illustrative preliminary strip, take an assumed uniform load q = 5.0 kN/m² over a 0.90 m span and a 1 m wide strip, giving line load w = 5.0 kN/m. The moment is M = 5.0 × 0.90² / 8 ≈ 0.51 kN·m per meter width, and the shear is V = 5.0 × 0.90 / 2 ≈ 2.25 kN per meter width. These figures set the demand side; they are not an allowable capacity, which is read from the section datasheet.

QuantityFormulaIllustrative result
Line loadw = q × strip width5.0 kN/m
Bending momentM = wL²/8≈ 0.51 kN·m per m
Shear forceV = wL/2≈ 2.25 kN per m
Section capacityPer datasheetCompared against demand

The demand is then compared with the section's bending and shear capacity from the datasheet, together with the sag limit. Where either demand approaches its limit, the depth or profile is increased or the span reduced; the governing condition is recorded rather than assumed from the underfoot feel.

5. Boundary: Design Stresses and Deflection

This note covers the preliminary distinction between bending and shear demand. It does not set permissible stresses, long-term creep factors, connection capacity or deflection acceptance, and it does not replace a structural calculation to the adopted standard.

A section sized for one span and load should not be carried to a longer span or heavier duty without re-checking both bending and shear. Where the duty changes, the governing demand may move from one condition to the other and the section is reassessed accordingly.

6. Frequently Asked Questions

What is the difference between bending and shear in a grating bar?

Bending curves the bar between supports and gives tension/compression across the depth; shear slides the bar near its support. Both are checked against the section capacity.

Which usually governs a long grating span?

Long spans are generally bending- and deflection-controlled because the moment grows with the square of the span; depth is added mainly to control sag and bending stress.

When should shear be checked?

On short, deep spans where the bar is deep relative to its length, shear at the support can govern before bending; check it even when bending looks comfortable.

What formulas frame the preliminary check?

For uniform load: M = wL²/8 and V = wL/2; for a central point load: M = PL/4 and V = P/2. Capacity comes from the datasheet, not these formulas.

Does bar depth alone determine the section?

No. Profile family changes stiffness and shear area; compare bending, shear and deflection demand against the datasheet for the chosen profile.

ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026 |Category: Structural Mechanics |Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating Surface Selection | R13
📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]