/>

Ammonia Solution 25% and FRP Grating: Liquor Splash and Alkali Vapour

Chemical Resistance
Direct Answer

Match the resin to the recorded ammonia strength and vapour/liquid mode, choose a damp-zone traction finish, seal every cut edge, isolate fixings, and supply concentration, temperature and drainage in the RFQ; suitability for the recorded conditions is confirmed by project review.

  • Ammonia liquor is alkaline and volatile; polyester is a mild-alkali starting point only, with tougher families reviewed for stronger alkali, warmth or steady mist once strength and vapour/liquid mode are recorded.
  • Pultruded I-bar follows aisle and platform runs; molded 38 mm panels follow valves, containers and channel openings. Span, access.
  • Grit top for pads where feet stay damp; concave dished sections shed condensate on ledges, and smooth mesh stays away from the splash and mist line. Site-cut edges and holes seal before the panel returns to the vapour zone.

How this article differs: This page covers the ammonia liquor/vapour duty and procurement inputs; it does not re-derive load tables, concentrated-load checks or resin chemistry, which are handled in the dedicated reference articles.

1. Site Conditions and Duty

Ammonia solution (ammonium hydroxide) is stored and dosed in fertilizer plants, refrigeration systems, water treatment and reagent preparation. Grating in the tank surround, dosing aisle and valve platform meets liquor splash when couplings or hoses are handled, drips from pump glands, and moist alkali vapour that settles on bars and ledges. The aisle is damp around transfer cycles; residue after rinsing can leave an alkaline film, and vapour carries a strong odour that signals ventilation and local contact. Walking rounds and occasional container handling are the main loads.

Ammonia liquor is alkaline and volatile; vapour plus moisture can attack a less compatible matrix, while condensation on cool bars keeps the panel wet between cycles. The resin family must be reviewed against the recorded liquor strength, temperature and whether contact runs as splash, vapour or pooled liquid; polyester is a general mild-alkali baseline only, and tougher families are considered for stronger alkali, warmth or steady mist after the resistance check. An unsealed edge lets moist vapour reach the reinforcement, which is why cut-edge sealing and clip isolation carry real weight in this duty.

2. Build-up, Resin and Surface Selection

LocationExposure modeDutySuggested build-upResin / surface note
Tank surround aisleLiquor splash, alkali mist, damp deckRounds around storage and pumpsPultruded 38 mm I-barResin per recorded medium; grit top
Dosing valve platformGland drips, vapour condensateValve and sample accessMolded 38 mm 38×38Matched family; concave shed
Channel / sump coverRunoff film, pooled rinseCover over drainage channelPultruded 38 mm T-barSealed edge; concave shed
Container changeover ledgeIntermittent splash, wipe-downStanding reach on transferMolded 38 mm 50×50Grip finish where damp
  • Ammonia liquor is alkaline and volatile; polyester is a mild-alkali starting point only, with tougher families reviewed for stronger alkali, warmth or steady mist once strength and vapour/liquid mode are recorded.
  • Pultruded I-bar follows aisle and platform runs; molded 38 mm panels follow valves, containers and channel openings. Span, access.
  • Grit top for pads where feet stay damp; concave dished sections shed condensate on ledges, and smooth mesh stays away from the splash and mist line. Site-cut edges and holes seal before the panel returns to the vapour zone.

3. Installation and Bearing Details

  • Level the aisle bearers and channel ledges, clearing alkaline deposit before dry-fitting; an uneven seat traps moisture at panel edges.
  • Bed sections on the 3 mm neoprene isolation strip over steel, keeping end and side gaps from the node detail around tank valves and couplings.
  • Secure each bar at every bearer and corner with the matching A2-70 M6/M8 clip family; isolate the fixing from dissimilar metal and hand-tighten to setting without over-driving.
  • Seal cut edges and drilled holes within 24 hours; lift removable covers without prising neighbours, then re-check bearing and clips after the first two weeks of vapour service.
Installation basis (locked facts):
  • ≥ 50 mm bearing on steel/FRP support; 60 mm preferred at end spans
  • 3 mm neoprene strip on steel supports to cut galvanic contact and local stress
  • 10–15 mm end gap for thermal movement (~20 mm at long runs)
  • 6–10 mm side gap for expansion and safe lifting
  • Clips at every support and every corner; C/L/T/W/saddle families; A2-70 M6/M8 bolts
  • Hand-tighten plus 1/4 turn; do not over-torque
  • Seal any cut edge with matched resin within 24 hours
  • Walk the deck and re-torque after 2 weeks of service

4. Routine Inspection and Maintenance

TaskFrequencyWhat to check
Visual inspectionMonthlyCracked bars, loose clips, edge seal, displaced panels
Clip torque checkQuarterly, first yearHand-tight; re-torque any loose fixing
WashdownAs neededFresh water, low pressure; no acid or solvent-based cleaner
Grit top renewalAs neededTop up worn traction with matched gritted resin
Edge seal checkAnnuallyTouch up any bare roving before it spreads
UV top-coatEvery 3–5 yearsRe-coat exposed surface with matched resin on request
  • Walk the aisle and platform monthly for dulled bars, loose clips, shifted panels and alkaline film in damp corners.
  • Check clip torque quarterly in year one; free any seized coupling or valve fitting before it locks under residue.
  • Rinse with fresh water at low pressure; keep reciprocal alkali cleaners and solvents off the resin matrix.
  • Renew worn grit with matched gritted resin and touch up exposed roving at edge seals before undercutting spreads along the channel.

5. RFQ Inputs and Procurement Checklist

  • State the ammonia liquor concentration range and recorded operating or ambient temperature, plus whether contact is liquid splash, vapour or both.
  • Describe drainage and pooling: runoff to channel, pooled liquor in a sump, or condensate held on ledges, with typical contact duration.
  • Give the duty: aisle rounds, hose or container changeover, valve sampling or equipment reach, and any local load from tools or drums.
  • Mark finishes by zone: grit on wet pads, concave on ledges, smooth on dry sheltered points.
  • Cite the governing standard and deflection limit; request the matched deflection report, batch material record and Barcol check with the production papers.
Procurement evidence basis (locked facts):
  • Governing access standard and project deflection limit are cited with the order.
  • Matched resistance note confirms the resin grade against the recorded medium.
  • Batch material record and Barcol hardness check accompany the delivered panels.
  • Any point, wheel, concentrated or equipment load is referred to engineer review and the matched report.
Minimum order (MOQ)10 m²
Standard production15–25 working days after drawing approval
Overall lead time12–36 working days overall
Indicative priceUSD 15–95/m²
Manufacturing historyFounded 2004; 200+ employees; 20,000+ m² plant
Export reach45+ countries; 541+ customer reviews, 4.9/5 average rating

6. Compliance and Service Boundaries

Boundary. This page does not assign a fire class or publish point, wheel or concentrated-load capacities. Rail lateral loads, uplift fixing, ventilation design and seismic design need project-specific engineering and the matched report. Ammonia service must be evaluated against the resin and cure system, concentration, temperature, stress and exposure mode; vapour and liquid duties are assessed separately, and no immersed or concentrated duty is cleared from the table alone.

7. Frequently Asked Questions

Which resin suits ammonia solution and alkali vapour on grating?

The grade follows the recorded liquor strength, temperature and whether contact is splash, vapour or pooled liquid. Polyester is a mild-alkali baseline; more resistant families are considered for stronger alkali, warmth or steady mist after the resistance check. Vapour and liquid duties are evaluated separately.

Pultruded or molded in an ammonia aisle?

Pultruded I-bar carries aisle and platform runs with lighter weight; molded 38 mm sections shape cleanly around valves, containers and channel openings. The measured span, access and fittings decide the mix.

What finish handles a damp vapour aisle?

Grit-embedded top for pads where feet stay damp; concave dished sections shed condensate on ledges; keep smooth panels off the splash and mist line. Match the opening to site footwear.

How are panels isolated in an alkali vapour zone?

Sections bed on the 3 mm neoprene strip; matching clips fasten bars to bearers and corners with the fastener isolated from dissimilar metal. Cut edges and holes are sealed within 24 hours; clearances follow the node drawing.

What ammonia-related damage should be reviewed?

Dulled or softened skin, darkening, lifted roving, cracked seal, persistent odour on bars or film under clips should be flagged for engineering review; a laminate opened to the glass needs assessment rather than a surface coat.

ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026 |Category: Chemical Resistance |Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating Surface Selection | R13
📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]