📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
FRP Pultruded Profiles

FRP Angle — Pultruded L-Profile

The cheapest way to finish an edge, brace a corner or carry a light stringer. Angles are the profile most often missing from a take-off until the deck edge needs a detail, and the one that holds a surprising number of small structures together.

What an angle is for

An L-section is two flanges at right angles with no web. It is inefficient as a beam and excellent as a detail: it supports a panel edge, it forms a corner between two members, it gives a bolted connection a face at ninety degrees, and it can be cut and drilled on site with hand tools.

On a grating deck the angle usually appears three times: as edge trim where the panel meets a wall or a curb, as the corner brace that stops a frame racking, and as the small member under a light tread or a step.

Where it earns its place

  • Edge trim and nosing along a deck perimeter, where the panel edge has to be closed and feet have to be kept off the open mesh.
  • Corner reinforcement of rectangular frames, particularly where a frame is bolted rather than braced.
  • Stair nosing and tread supports on small FRP stair units.
  • Support angles for light covers, hatch surrounds and equipment plinths.
  • Equal and unequal legs: an unequal angle carries more load on the long leg and is used where a wide bearing face is needed on one side only.

Limits

An angle has almost no torsional stiffness and very little capacity as a beam, because there is no web to separate the flanges. Loaded on one leg it bends about an axis close to the other leg, and the section twists as it does so. Where a member has to carry load over any distance, it should be a channel or an I-beam; the angle belongs at the detail.

The second limit is the corner itself. A pultruded L-section has a resin-rich inside corner and a thin outside corner, and it is the weakest part of the profile. Bolting through both legs close to the corner is normal; putting a bolt right at the corner, or a load that pries the legs apart, is not.

Detail notes

Edge trim is usually the angle with its long leg vertical, capping the panel edge, and the short leg under the deck as a bearing face. Where a person can stand at the edge, the trim also becomes the thing that stops a boot slipping into the gap, so the leg that faces up should be thick enough not to deflect under a foot.

Corner braces are cut at forty-five degrees or square, bolted through both members. On a pultruded frame the brace is what converts a rectangle into a truss, and omitting it is the most common reason a small FRP frame racks on site.

Specifying an FRP angle

  • Leg lengths, leg thickness, and whether the angle is equal or unequal.
  • Grade to BS EN 13706 with the modulus, particularly where the angle is used structurally rather than as trim.
  • Resin and finish: isophthalic polyester with a UV-stable surface for outdoor edge trim.
  • Cut list per leg, because an angle is often ordered as two different cut lengths from the same stock.
  • Whether the detail needs the legs drilled or field-cut, since site drilling of pultruded profiles needs a sharp bit and slow feed to avoid delamination.

Related pages

FAQ

What is a pultruded FRP angle used for?
Edge trim, corner bracing, stair nosing, light tread supports and small plinths. It is a detail profile rather than a spanning member.
Can an angle be used as a beam?
Only over short distances and light loads. With no web, the section has little torsional stiffness and bends about an axis close to the second leg.
Equal or unequal angle, which do I need?
Equal legs where the angle works in both directions, such as a corner brace. Unequal legs where one side needs a wide bearing face, such as edge trim or a tread support.
Will an FRP angle corrode at the corner?
The pultruded corner is resin-rich and is not the weak point for corrosion. The joint is: where a stainless bolt meets the FRP, isolate the contact or expect the first sign of attack there.
What grade of angle do you supply?
E17 or E23 to BS EN 13706. For trim the grade matters less; for bracing it should be declared.
Can angles be cut and drilled on site?
Yes, with a diamond or carbide blade and a slow feed. Fast drilling heats the resin and can delaminate the profile at the hole.

Fiberglass Equal Angle and Fiberglass Unequal Angle: L-Shaped Pultruded Sections for Frames and Brackets

The Fiberglass Equal Angle (two equal legs) and the Fiberglass Unequal Angle (one long, one short leg) are the workhorse L-sections of pultruded construction. Equal angles brace frames and edge-trim walkways; unequal angles sit where one leg must fix to a slab or beam flange while the other carries a cladding or bracket load. Both resist rust, conductivity and chemical attack where steel would corrode within months.

Pultruded FRP Structural Profiles Across the I Beam, Angle, Channel and Tube Family

Angles are one member of the wider family of Pultruded FRP Structural Profiles: I-beams and H-columns for bending, channels and U-sections for troughs and cable trays, rectangular tubes for handrail posts and low-profile frames, and custom T, Z and hat sections. Mix families on one structure — all cut to the same length list and shipped together. See the FRP profiles index and the structural profiles library for the full family.

Material, Resin and Machining: How We Build Pultruded Angles

Each angle is pulled from continuous E-glass roving (60–75% by weight) with a surfacing veil for a resin-rich outer skin. Isophthalic polyester suits atmospheric and freshwater exposure; vinylester is for acid, alkaline and marine splash; polyurethane gives a smooth UV-stable surface. Sections are drilled, routed and cut on site with carbide or diamond tooling at slow feed — fast drilling heats the resin and delaminates the leg. We are a direct FRP manufacturer since 2004 (20,000+ m² plant, 40+ export countries); stock angles ship in 7–35 working days.

Pultruded Angles: Frequently Asked Questions

Can you open a custom die for a non-standard angle leg size?
Yes. We design pultrusion dies for equal and unequal leg angles from your drawing. Tooling takes typically 4–8 weeks; samples are approved before serial production.
What is the MOQ and lead time for pultruded FRP angles?
MOQ starts at 10 m² equivalent for stock angles; custom dies require a minimum run agreed on the drawing. Standard lead time is 7–35 working days after order confirmation.
Which export trade terms do you support for angles?
We ship EXW our factory, FOB Shanghai / Ningbo and CIF to your nominated port, with sea-worthy crating and full export documentation.
Terminology

L Profile, L Angle and the Rest of the Pultruded Structural Family

FRP L profile, L angle and FRP angle: equal-leg, unequal-leg and custom sections

An FRP L profile, an L angle and an FRP angle are the same 90-degree section: two legs at right angles, pultruded with the rovings running along both legs. Equal-leg sizes are stocked (25×25 up to 100×100 mm, 3–12 mm thick); unequal-leg and thick-wall variants are pultruded to order. Buyers use it as edge angle on walkways, as a corner stiffener on frames and as a cable-tray side rail, because it bolts on without welding and never needs re-coating.

The leg thickness and the resin, not the name, decide the duty. Isophthalic polyester suits general outdoor and wash-down service; vinyl ester is specified for acid mists, chlorides and pulp bleach halls. Both are covered by ISO 9001 (01708Q11888R0S) and quoted from drawings, MOQ 10 m² equivalent.

Pultruded FRP structural profiles — GRP and fiberglass I beam, angle, channel and tube from one supplier

The angle does not travel alone. Pultruded FRP structural profiles cover the whole family: GRP and fiberglass I beam for bending spans, angle for edges and corners, channel for joists and cable trays, tube for posts, handrails and ladder rails. Supplying them from one pultrusion line means the sections share resin, colour and certificate, and arrive on one packing list instead of four.

Browse the shape pages — FRP I beam, FRP channel, FRP rectangular tube — or the full range on FRP profiles. Frames built from these sections carry pultruded FRP grating decks.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]