📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
Product family

FRP Pultruded Profile Shapes

Nine shape pages, one per section, because a channel and an I-beam are not the same product and a buyer searching for one should not land on a page about the other. Each page states what the section carries, where it belongs on a grating deck, and what the connection detail has to do.

The nine shapes

ShapePageSection logic
I-beam/products/frp-profiles/beam/Most efficient per kilogram in bending; the default bearer
Channel (U)/products/frp-profiles/channel/Half the bending, but an open web that bolts easily
Angle (L)/products/frp-profiles/angle/A detail profile: edge trim, corner brace, nosing
Flat bar/products/frp-profiles/flat-bar/Bearing plates, edge strips, rungs and shims
Round rod/products/frp-profiles/round-rod/Ties, pins and machined inserts; strongest in tension
Square rod/products/frp-profiles/square-rod/Flat-faced spacers, locating blocks and light frames
Round tube/products/frp-profiles/round-tube/Closed circle: handrail, posts, struts, torsion
Square tube/products/frp-profiles/square-tube/Posts and frames; the easiest section to bolt at a corner
Rectangular tube/products/frp-profiles/rectangular-tube/Depth where width is not available; stiles and shallow frames

One standard, two grades

Every profile on this site is pultruded to BS EN 13706 and declared as grade E17 or E23. The standard defines grades by measured mechanical property, so a buyer can check the member against a load case instead of trusting an adjective.

Grade E17 is the general structural grade and covers most bearers, stringers, posts and framing. Grade E23 carries a higher modulus and is used where deflection governs rather than strength, such as long spans or where a walkway has to feel stiff. The number that settles deflection is the modulus, and it should appear on the datasheet beside the grade.

How the shapes are chosen

In practice the section is chosen by the load path, not by preference. A member that spans between columns is in bending, so it wants an I or a deep rectangle. A member that receives a bolted connection wants an open web or a flat face, so it wants a channel, a tube or a bar. A member that a person grabs or that twists wants a closed round or square section. A member whose job is to close an edge wants an angle.

Where the deck is the product and the frame is the afterthought, this is the decision that gets skipped, and it is the one that shows up on site as a bouncing platform or a post that leans.

Related families

  • GRP structural profiles overview, with the standards and the grade comparison
  • FRP plate and flat sheet for solid surfaces
  • FRP handrail systems, built from round and square tube
  • Grating clips and fasteners for the deck above the bearers
  • Span and load calculator for the grating panel itself

Related pages

FAQ

What shapes of FRP profile do you pultrude?
I-beam, channel, angle, flat bar, round rod, square rod, round tube, square tube and rectangular tube, with custom dies for other sections.
What standard are the profiles made to?
BS EN 13706, declared as grade E17 or E23 with the modulus stated on the datasheet.
Which shape is strongest?
For bending, an I-beam or a deep rectangular tube. For torsion and for members that are grabbed, a round tube. There is no single strongest shape, only the right shape for the load path.
Can I get custom profile dimensions?
Yes. Custom dies are made for non-standard sections, with a tooling lead time that is quoted with the drawing.
Do you cut profiles to length?
Yes, to a cut list, with square-cut ends as standard and prepared ends where a connection detail requires them.
What resin systems are available for profiles?
Isophthalic polyester as standard, vinyl ester for chemical service and higher temperature, with a UV-stable surface finish for outdoor work.
Roof support

FRP Purlin for Roof Support: C and Z Sections That Outlast Steel

An FRP purlin for roof support is a pultruded C or Z section that carries roof sheeting across the rafters or steel frame, where galvanised steel purlins would corrode in coastal, chemical, wastewater or agricultural atmospheres. Because the glass fibres run the full length, a GRP/FRP purlin resists acid, alkali and salt fog without painting, and stays dimensionally stable where steel rusts through its fixing holes.

C sections bolt up the web and suit wall sheeting and small overhangs; Z sections lap over the top chord for continuous-roof multi-span layouts. Purlins are fixed to the rafter or the primary frame with self-drilling screws and neoprene-sealed washers, and the roof sheet clips or screws to the top flange. Design is deflection-governed: size the C or Z depth on the rafter spacing and the imposed roof load, and confirm the modulus as E17 or E23 to BS EN 13706 rather than a generic 'structural' label.

Purlin typeTypical depthBest fixingRecommended resin
C purlin100 – 150 mmWeb bolting, wall sheeting and short overhangsIsophthalic polyester for general humidity
Z purlin150 – 200 mmTop-chord lapping, continuous multi-span roofsVinyl ester for coastal and chemical atmospheres
Why composite

Why Specify an FRP Purlin Instead of Galvanised Steel

A pultruded FRP purlin is around a quarter the weight of a comparable steel purlin, so roof dead load and rafter sections shrink at the same time. It is non-sparking and non-conductive, which matters in wastewater plants, paper mills, battery rooms and coastal substations, and it will not corrode where the fixing holes on galvanised steel start to weep. It cuts, drills and slots on site like timber but never rots.

Terminology: FRP, GRP and GFRP purlins are the same pultruded glass-reinforced section; fiberglass (US) and fibreglass (UK) are one fibre. C and Z purlins, roof supports and structural sections all belong to the pultruded shapes family. Choose the cross-section on this shape-selection page, compare technical grades on the structural sections overview, and arrange OEM tooling, MOQ and export on the manufacturer page. The FRP grating supplier desk pairs these roof members with raised floors and walkways below.

FAQ

FRP Purlin for Roof Support — Frequently Asked Questions

Can you pultrude a custom C or Z purlin cross-section?
Yes. We cut new steel dies in-house for custom C and Z depths, lipped angles and integrated fixing slots. Send a drawing or sample and we confirm feasibility, glass content and tooling lead time.
What is the minimum order quantity for FRP purlins?
Our minimum starts at 10 m² equivalent of profiles. Standard C and Z sections can be quoted in smaller trial quantities for a new roof project.
Which export terms and lead time apply to roof purlins?
We ship EXW, FOB Shanghai or CIF to your destination port, sea-worthy crated. Standard lead time is 12–36 working days after order confirmation, depending on resin system, tooling and length. Oversized panels, custom colours, new moulds and specialty resins are quoted with a separately confirmed schedule.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]