📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
FRP Pultruded Profiles

FRP Channel — Pultruded U-Profile

Half the bending efficiency of an I-beam at the same depth, and twice as easy to bolt. The channel is the profile that gets used at the edge of a deck, in a stringer, and wherever a connection has to pass through a web.

What the shape is good at

A channel is an I-beam with one flange removed. It keeps most of the bending capacity in one direction, loses torsional stiffness, and gains the one thing a fabricator needs: an open web you can drill through from the side without a special detail.

That is why channels appear at the perimeter of a platform, as stair stringers, as the rails of a frame and as the member a handrail post bolts into. The moment demand at a deck edge is low; the connection demand is high, and the channel serves the connection.

Where it fits on a grating deck

  • Perimeter edge member, where the deck meets a wall, a stair or a handrail line.
  • Stringer under the panel joints, where the channel web gives the clip a straight surface to bolt against.
  • Frames for equipment skids, cable trays and small platforms built from a single section size.
  • Stair stringers on FRP stair units, where the channel carries the treads and takes the bolted connections at both ends.

The trade-off you accept

Two things go missing when the second flange is removed. The section modulus about the weak axis drops sharply, so a channel loaded on its side, or a channel acting as a strut with an eccentric load, is a much weaker member than the drawing suggests. And the open section twists more readily, so a channel used as a compression member needs bracing that an I-beam would not.

The other trade-off is galvanic and thermal, not structural: a channel is often the member that receives a stainless bolt through its web, and that is exactly where dissimilar materials meet. Isolate the joint or accept that the contact point is the first place corrosion will show.

Details that decide whether it works

Cut the channel ends square and, where it meets an I-beam, bolt a plate to both webs rather than relying on a single bolt. Where the channel carries a clip line, the clip spacing follows the panel supplier, not the steel detail: a clip every panel joint and every support line, not a fixed distance.

Where a channel is used as a handrail post base, the post is a square tube that passes through a hole in the channel web or bolts to a plate welded to a pultruded base. The bolted plate detail is the one that fails first if it is under-designed.

Specifying an FRP channel

  • Depth, flange width, flange thickness and web thickness as a drawing.
  • Grade to BS EN 13706, E17 or E23, and the modulus that goes with it.
  • Resin: isophthalic polyester as standard, vinyl ester for chemical or higher temperature service.
  • Whether the profile is used in bending or as a strut, because the two call for different bracing.
  • Cut list, and whether the ends are square cut or require bolt plates.
  • UV-stable finish for outdoor work and a colour reference for the whole order.

Related pages

FAQ

What is a pultruded FRP channel used for?
Perimeter members, stringers, stair stringers, equipment frames and the base a handrail post bolts into. It is chosen where a bolted connection through a web matters more than pure bending efficiency.
Is a channel weaker than an I-beam?
About half the bending capacity at the same depth in the strong direction, and considerably less about the weak axis. Where the load is purely bending, an I-beam is the better section.
Can a channel be used as a column?
Only with bracing. The open section twists easily, and a slender channel in compression buckles or twists at a load well below its squash load.
Which side of the channel should face up?
The web normally faces the connection and the flanges face the deck, so clips and bolts land on a flat surface. Where the channel is a stringer under a panel joint, the flange pair also gives the clip a bearing surface.
What grade of channel do you supply?
E17 or E23 to BS EN 13706, with the grade and measured modulus stated on the datasheet.
Do you supply channels cut to a cut list?
Yes, cut to length with square-cut ends, and with bolt plates or prepared ends where the connection design calls for them.

FRP C Channel and Fiberglass U Section: Pultruded Trough Profiles for Railing Bases and Cable Trays

The FRP C Channel (open trough, single web with two return flanges) and the Fiberglass U Section (deeper, fully open U) are the pultruded workhorses for railing bases, cable tray, edge protection and machine guarding. Both resist rust in coastal, wastewater and chemical plants, are non-conductive for electrical areas, and weigh roughly one quarter of a steel channel of equivalent stiffness.

How We Pull a Channel: Roving, Resin and Wall Tolerance

Each channel is drawn from continuous E-glass roving (60–75% by weight) with a surfacing veil for a resin-rich corrosion skin. Isophthalic polyester suits atmospheric and freshwater exposure; vinylester is for acid and alkaline splash; polyurethane gives a smooth UV-stable surface. Wall thickness and flange width are held to pultrusion tolerances, and sections are cut to a length list with prepared ends. See the FRP pultruded profiles range and the structural profiles library; we are a direct FRP manufacturer since 2004 (20,000+ m² plant, 40+ export countries), shipping in 7–35 working days.

Pultruded Channels: Frequently Asked Questions

Can you open a custom die for a non-standard FRP channel width?
Yes. We design pultrusion dies for C-channels and U-sections of custom width and depth from your drawing. Tooling takes typically 4–8 weeks; samples are approved before serial production.
What is the MOQ and lead time for FRP channels?
MOQ starts at 10 m² equivalent for stock sections; custom dies require a minimum run agreed on the drawing. Standard lead time is 7–35 working days after order confirmation.
Which export trade terms do you support for channels?
We ship EXW our factory, FOB Shanghai / Ningbo and CIF to your nominated port, with sea-worthy crating and full export documentation.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]