📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
Marine & Offshore FRP Grating · Salt-Resistant · Corrosion-Proof

Marine FRP Grating

Marine & Offshore FRP Grating · Vinyl Ester · UV/Stable · Non-Corrosive — fiberglass grating built for salt spray, bilge and offshore deck environments.

ISO 9001 Certified
Direct FRP Grating Master Factory
Exported to 45+ Countries
ISO 9001
Quality Management
45+ Countries
Global Export Network
20+ Years
Manufacturing Experience
Custom OEM/ODM
Engineering Support

Marine and offshore FRP grating survives the harshest corrosion environment — constant salt spray, bilge water and UV. FRP Grating Master supplies fiberglass grating in vinyl ester and UV-stabilised polyester that resists salt-water corrosion without the rust, painting and conductivity of steel. It is the standard flooring for offshore platforms, docks and jetties, boat and marina walkways, coastal structures and desalination plants.

Overview

Why FRP for Marine & Offshore

Salt & Corrosion Resistance

Vinyl ester and isophthalic resin systems withstand salt spray and immersion far better than steel or aluminium, with no rust and no ongoing painting.

Non-Conductive & Safe

FRP is non-conductive and UV-stable, with anti-slip gritted surfaces for safe wet-deck footing on offshore modules and coastal gangways.

Overview

Applications & Supply

Where Used

Offshore platform decks, docks and jetties, marina and boat walkways, coastal structures, desalination and seawater intakes. Pair with anti-slip surfaces and walkway grating.

Ordering

We supply vinyl ester marine-grade panels in 25/30/38/50 mm thickness. Browse products, custom sizes and request marine-grade supply via contact.

Technical Specifications

Marine FRP Grating Technical Specifications

Marine FRP grating is built for salt-laden, splash-zone and offshore service where steel walkways corrode within a few years. It normally uses vinyl ester resin, a gritted or covered anti-slip surface, and SS316 fixings. The table below lists the standard marine range.

Parameter38 mm Molded Marine50 mm Pultruded Marine75 mm Long-Span
Panel thickness38 mm50 mm75 mm I-bar
Mesh / bar spacing38×38 mm40 mm bar centres40×60 mm
Standard panel size1220×3660 mm1220×3660 mm1220×6000 mm
SurfaceGrit-top / CoveredGrit-topGrit-top
ResinVinyl esterVinyl esterVinyl ester
Recommended fixingsSS316 clipsSS316 clipsSS316 heavy clips
Typical useDeck walkwaysPlatforms, rampsLong offshore spans
Marine Comparison

FRP vs Steel in Marine and Salt Service

The reason offshore and marine specifiers choose FRP is not lower upfront price — it is eliminating rust, electrolysis and the maintenance that metal walkways demand in a salt environment.

PropertyMarine FRP GratingSteel Grating (Hot-Dip Galvanised)Aluminum Grating
Salt-spray resistanceExcellent (vinyl ester)Galvanising weathers; pitting returnsCan corrode around dissimilar metals
Electrical conductivityNon-conductiveConductiveConductive
Galvanic / electrochemical riskNoneAccelerates corrosion at contactsAccelerates corrosion at contacts
Weight~1/4 of steelHeavyLight but conductive
MaintenanceWash-down; near-zeroInspect & recoatPeriodic inspection
Service life offshore20+ years5–8 years without coating15–20 years
Resin Selection

Resin Selection for Marine Service

Salt water, salt spray and brackish splash zones demand the right matrix. Isophthalic polyester is acceptable for mild, occasional splash; vinyl ester is the standard for continuous marine and offshore duty.

ResinRelative CostSalt / Chemical ResistanceFire RatingBest For
Isophthalic polyesterBaselineGood; occasional splashASTM E-84 Class BHarbour-side promenades
Vinyl ester+15–25%Excellent (salt, H2S, brackish water)ASTM E-84 Class BOffshore decks, jetties, ship walkways
Phenolic+20–35%Moderate; low smokeASTM E-84 Class AAccommodation modules, enclosed decks

Compare systems in the vinyl ester vs polyester guide.

Load & Span

Offshore Load and Span Performance

Offshore decks often need long, light spans. Pultruded I-bar grating reduces support steel — and reduces the number of welded connections where corrosion starts.

ApplicationRecommended PanelTypical SpanFixing
Walkway stairs & treads38 mm molded450–600 mmSS316 clips
Working platform50 mm molded / pultruded600–900 mmSS316 clips
Long unsupported deck75 mm I-bar pultruded900–1200 mmSS316 heavy clips
Installation

Marine Installation Guide

  1. Check drawings and confirm bearing support; lay panels on clean, level steel or GRP beams with the recommended bearing width on each support.
  2. Pre-drill fixing holes only where needed; align panels to the grid and leave a 10–15 mm expansion gap between adjacent panels.
  3. Fasten with stainless steel FRP grating clips — minimum 4 clips per 1220×3660 mm panel, one at each corner, plus extra clips for heavy traffic or wind-uplift zones.
  4. Cut panels with a carbide-tipped or diamond blade; wear dust protection and seal cut edges on vinyl ester or phenolic panels when required.
  5. Walk the installed grid to check deflection and clip torque, then clear offcuts and install edge trim or toe-kicks where specified.

Always use SS316 (or higher) fixings in salt service — never plain steel or SS304 in splash zones. See the marine clip range and FRP handrail systems for compatible corrosion-proof guardrails.

Applications

Marine and Offshore Applications

Offshore platforms: non-conductive vinyl ester grating forms walkways around process decks, eliminating electrolytic corrosion between the walkway and the steel jacket — a known failure mode for metal gratings fixed to offshore structures.

Marinas, jetties and docks: FRP grating over pontoons resists constant salt spray and wet footing, and its light weight simplifies installation on floating docks.

Ship decks and seawater intake: around seawater cooling systems and coastal pump houses, GRP panels do not rust-stain and resist H2S from degrading seawater. See offshore application notes.

Marine Specifics

Salt Spray, Non-Conductivity and Electrochemical Corrosion

In a marine atmosphere, salt is an electrolyte. When two dissimilar metals are wet-connected, a galvanic cell forms and the less noble metal corrodes rapidly. Because FRP grating is non-conductive, it breaks that circuit — no galvanic couple between walkway and structure, and no stray-current corrosion at fixings. Vinyl ester panels also survive extended salt-spray exposure (ASTM B117-type testing) without blistering or loss of strength. Together these properties are why offshore and naval specifiers treat marine FRP grating as standard rather than optional.

Related Pages

Related Products and Guides

Get Started

Dock Fiberglass Deck Grating

Dock fiberglass deck grating gives pontoons, jetties and boat docks a salt-proof, non-slip deck that never rusts or splinters in marine use.

Offshore Pultruded FRP Grating

Offshore pultruded FRP grating is specified for platform decks and walkways where salt, spray and maintenance downtime rule out steel.

Marine Pultruded FRP Deck Grating

Marine pultruded FRP deck grating is the long-span, non-skid decking for boats, pontoons and coastal structures.

Request Your Marine FRP Grating Quote

Email [email protected] · Tel/WhatsApp +86-513-6681-9918 · Nantong, Jiangsu, China

FAQ

Marine FRP Grating FAQ

Why use FRP grating in marine and offshore environments?
FRP/GRP grating resists salt spray and seawater corrosion without rust, painting or conductivity — unlike steel or aluminium — making it ideal for offshore decks, docks and coastal structures.
Which resin is best for marine use?
Vinyl ester or isophthalic polyester offers the best salt and chemical resistance; UV-stabilised resin is recommended for long-term outdoor offshore exposure.
Is marine FRP grating anti-slip?
Yes. Gritted anti-slip surfaces provide safe wet-deck footing on offshore modules, docks and gangways.
Where is marine FRP grating used?
On offshore platforms, docks and jetties, marina walkways, coastal structures, desalination plants and seawater intake structures.
Why is FRP grating used on offshore and marine platforms?
Because it is non-corrosive, non-conductive and light. It resists salt spray, avoids the galvanic corrosion that metal gratings suffer when wet-connected to steel structures, and installs quickly on offshore decks.
Does FRP grating resist salt water and salt spray?
Vinyl ester FRP grating is specified for continuous salt-water and salt-spray service and shows no rust, pitting or blistering in extended exposure. Isophthalic polyester suits only occasional splash.
Why does non-conductive grating matter around marine structures?
A conductive metal walkway can create a galvanic cell with the steel jacket, accelerating electrochemical corrosion at the contacts. Non-conductive FRP breaks that circuit and removes this corrosion path.
Which resin is best for marine FRP grating?
Vinyl ester is the standard for continuous offshore, jetty and splash-zone duty. Phenolic is chosen where low smoke is required on enclosed decks, and isophthalic polyester for lighter harbour-side use.

Technical Documentation (PDF)

Download the FRP/GRP technical documents relevant to this page. Figures are indicative — confirm against a stamped project calculation.

Request a quotation or ask our engineers

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]