A panel transfers its end reaction into the support through the bar ends resting on the seat; the local contact pressure under those ends must be checked against the permissible bearing of the composite.
- Confirm the bar end rests on a seat of adequate length and solid bearing.
- Estimate bearing pressure as end reaction divided by the contact area per bar.
- Local bearing at edges, cut panels or heavy reactions needs engineered review.
1. Where a Panel Bears on Its Support
At each support line, the panel does not hang from its fixings; its bar ends sit on the framing and transfer the reaction into the seat beneath. The contact between the bar end and the support is a local compressive condition, concentrated over the bearing length and the bar width rather than spread across the whole panel.
If the bearing seat is too short, uneven or partially over a gap, the contact pressure rises on the remaining portion of the bar end. A panel that looks seated from above may still bear poorly if the support top is out of level or the bar end only touches a narrow edge.
- bearing length. the length of bar end resting on the support seat, measured along the span.
- bar width. the face width of the contacting bar, perpendicular to its depth.
- end reaction. the support force transferred from a bar or panel into the framing at a bearing line.
- bearing pressure. the compressive contact stress between the bar end and its seat.
- permissible bearing. the contact pressure the composite may carry, taken from datasheet or design.
2. Bearing Pressure Formula at the Bar End
For a bar end carrying reaction R over contact width b and bearing length L_b, the average bearing pressure is p_b = R / (b · L_b). This contact area is the seat beneath that single bar; neighboring bars carry their own reactions separately. The result is compared with the permissible bearing of the resin and composite from the datasheet or design standard.
The formula gives an average contact pressure over the seat; real contact can be higher at an uneven edge or a partially seated bar end. Where the seat is narrow, the panel is a cut section, or the reaction is heavy, the local condition should be reviewed rather than judged from the average figure alone.
- Measure the actual bearing length under the bar end, not the nominal panel edge.
- Confirm the seat is solid, level and in full contact along the bearing.
- Compare the computed pressure with the permissible bearing for the material.
3. Worked Example: End Reaction and Seat Length
As an illustrative check, take an assumed end reaction R = 2.0 kN on one bar, a bar width b = 10 mm and a bearing length L_b = 50 mm. The contact area is b·L_b = 10 × 50 = 500 mm², and the bearing pressure p_b = 2000 N / 500 mm² = 4.0 N/mm². This is the preliminary contact estimate; whether it is acceptable follows the permissible bearing stated for the chosen section and resin.
| Input | Symbol | Worked value |
|---|---|---|
| End reaction | R | 2.0 kN (assumed) |
| Bar width | b | 10 mm |
| Bearing length | L_b | 50 mm |
| Contact area | b·L_b | 500 mm² |
| Bearing pressure | p_b = R/(b·L_b) | 4.0 N/mm² |
| Seat condition | Bearing implication |
|---|---|
| Full level contact | Pressure distributed over the bearing length |
| Short or narrow seat | Higher pressure on the remaining contact |
| Partially seated bar end | Local edge concentration above the average |
| Uneven support top | Contact may ride on one edge of the bar |
4. When Local Bearing Needs Review
Cut and trimmed panels, openings where a bar end meets a frame, and decks carrying heavy equipment or concentrated reactions are the cases most likely to need a bearing check. At these locations the bar may be trimmed, the seat may be non-standard, or the reaction may exceed a typical walkway contact.
Signs of local bearing trouble include crushed or split edges, contact gaps under a seated panel, and bars rocking on an uneven support. Such conditions are inspected and corrected at the support rather than tightened down; a structurally damaged bar end is assessed for repair or replacement.
- Review bearing at cut panels, framed openings and heavy reaction points.
- Check for crushed edges, gaps and rocking after the panel is seated.
- Do not rely on the panel clip to carry the end reaction into the framing.
5. Boundary: Permissible Bearing and Connection
This note covers a preliminary bar-end bearing pressure check. It does not set permissible bearing values, design the anchor or clip connection, assess local crushing under impact, or replace a structural calculation to the adopted standard.
A bearing arrangement suitable for a light walkway should not be repeated under a heavy machine or a cut-out edge without re-checking the local pressure. Where the reaction or panel condition changes, the seat and contact are reassessed against the new load.
6. Frequently Asked Questions
How is grating bar-end bearing pressure calculated?
p_b = R/(b·L_b): end reaction divided by bar width times bearing length; compare the result with the permissible bearing for the chosen section and resin.
What happens if the bearing seat is too short?
The reaction concentrates on the remaining contact and the pressure rises; an uneven or partial seat can produce edge concentrations above the average estimate.
Do clips carry the end reaction?
Clips secure the panel; the bar end bears on the support seat to transfer the reaction. The fixing is not assumed to carry the bearing load into the framing.
Which panels need a bearing review?
Cut or trimmed panels, bars meeting a frame around an opening, and decks with heavy equipment or concentrated reactions should have local bearing checked.
What signs indicate a bearing problem?
Crushed or split edges, gaps under a seated panel and rocking bars on an uneven support point to a contact or levelness issue that should be inspected and corrected.
