/>

Bar Depth and Stiffness in the Molded Grating Range

Structural Sizing
Direct Answer

understanding how molded panel depth relates to stiffness and preliminary span selection

  • List the molded depths available and the span each is considered for in preliminary selection.
  • Deeper bars generally provide greater bending stiffness and a stiffer walking surface.
  • Record the panel weight trend with depth so the framing and lifting plan stay realistic.

1. Scope and Engineering Context

Bar depth is the main lever on bending stiffness within the molded family: deeper bars generally resist sag more readily and give a firmer underfoot surface. Yet depth is only one half of the decision, because span, duty, mesh density and panel weight all move together when a section is chosen from the molded range.

A preliminary pass lists the molded depths on offer and the spacing each is considered for, then checks how weight and open area change with that depth. The aim is a panel that keeps deflection within the contract limit without carrying more self-weight or cost than the deck needs.

  • bar depth. The vertical height of the molded bar, measured through the panel; it is the principal driver of bending stiffness in this family.
  • molded thickness. The molded panel thickness referred to interchangeably with bar depth; it sets how deep the spanning members are between bearings.
  • stiffness. Resistance to bending under the design load, reflected in sag between supports and in the firmness felt when walking.
  • deflection. The amount the deck deflects under load at the planned span, checked against the specified L/200 or tighter limit rather than against subjective bounce.
  • panel weight. The panel's own mass per unit area, which rises with depth and must be carried by the framing and accounted for in lifting.

2. Worked Example and Site Checklist

The verified molded weight and open-area rows show the depth trend. From 25 mm to 65 HD the panels run 12.5, 15.0, 19.5, 27.0 and 38.0 kg/m², with open area around 68%, 66%, 68%, 60% and 56% respectively; the 38 mm 40×40 mesh sits near 18.0 kg/m² at 70% open area. As bars go deeper, material per square metre rises and the mesh tends to close.

Converting the 38 mm panel's 19.5 kg/m² to imperial uses 0.2048 lb/ft² per kg/m², giving about 3.99 lb/ft². A full standard 1220 × 3660 mm 38 mm panel weighs about 87 kg. These figures are preliminary references; the exact mesh, resin and final weight must be confirmed on the order drawing and matched to the data sheet.

Check on siteWhat to recordWhy it matters
List molded depths against planned spansRecord each depth and the spacing it is reviewed atDepth and span have to be matched before stiffness can be judged.
Note stiffness expectation under loadRecord the contract deflection limit and walking dutyA firmer feel must be tied to a measured limit, not to thickness alone.
Track weight trend with depthCopy the kg/m² row for the shortlisted sectionHeavier panels affect framing, handling and lifting assumptions.
Check open area for the chosen meshRecord the open-area percentage and mesh sizeA deeper panel on a denser mesh may sacrifice drainage or visibility.
Flag any stiffness claim beyond the tableMark where a matched test report is neededPerformance outside the published rows cannot be assumed from depth.
ItemVerified figure / note
Molded 25 mm12.5 kg/m² · 68% open area
Molded 38 mm 38×3819.5 kg/m² · 68% open area
Molded 50 mm27.0 kg/m² · 60% open area
Molded 65 HD38.0 kg/m² · 56% open area

3. Failure Modes and Cautions

A common misread is equating thickness with guaranteed stiffness: a 25 mm panel laid over a long span sags even though the surface looks solid, because bar depth alone cannot compensate for a spacing outside its rated range. The section has to be checked against span and deflection limit, not judged by how thick it appears.

Another failure is upgrading depth to solve a stiffness problem that actually comes from mesh choice or an over-wide support spacing. Heavier bars add dead load to the framing; if the real cause is span or bearing, the added depth does not remove the underlying deficiency.

  • Confirm stiffness against the actual span and specified deflection limit before selecting a depth.
  • Check panel weight against the framing and lifting plan; a deeper section is not free to carry.
  • Open area and mesh density should be re-verified whenever depth or mesh changes on a drawing.

4. Boundary: When This Does Not Apply

This depth-and-stiffness discussion applies to preliminary molded selection under uniform load. It does not cover concentrated point loads, wheeled or rolling duty, cantilever projections, impact, fatigue life, snow load, or any derating under elevated or low temperature; those go to a separate structural assessment.

If the planned span or duty sits beyond the tabulated molded range, a deeper molded panel should not be assumed to close the gap; consider a pultruded T-bar or I-bar series and have the engineer confirm against a matched report. Surface cure, resin grade and chemical resistance are separate checks and are not inferred from bar depth.

5. Frequently Asked Questions

Does a thicker molded panel always feel stiffer?

Deeper bars generally increase bending stiffness and reduce sag under load, but stiffness must be checked against the actual span and deflection limit, not judged by thickness alone.

How much does panel weight rise with depth?

Indicative molded weights range from 12.5 kg/m² at 25 mm to 38.0 kg/m² at the 65 HD section, per the data sheet; confirm the exact mesh and resin on the order drawing.

Is there a minimum depth for a walkway?

Minimum depth follows span and duty from the table, not a fixed rule. A closely spaced light walkway and a long platform call for different sections.

Can I increase depth to reduce deflection on a long span?

Increasing depth helps within the rated range; for spans or duty outside the table, an engineer should review the section rather than upgrading by guesswork.

Where are molded weights and open area listed?

The molded weight and open-area rows are reproduced in the load table and technical data sheet; use those figures for preliminary estimates only.

ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026 |Category: Structural Sizing |Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating Surface Selection | R13
📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]