/>

When to Upgrade from 38 mm to 50 mm Molded Grating

Structural Sizing
Direct Answer

recognizing the conditions that justify a deeper molded 50 mm section

  • Compare the planned span and duty against the 38 mm molded table row.
  • Consider 50 mm where the 38 mm value is marginal at that span.
  • Account for tools, equipment or heavier pedestrian use on the deck.

1. Scope and Engineering Context

Moving from a 38 mm to a 50 mm molded panel is justified when the shallower section sits marginal at the planned span, or when tools, equipment or heavier pedestrian use demand more stiffness. The upgrade follows the duty and span, not a default assumption that deeper is always safer.

The comparison checks the 38 mm row against the real spacing, weighs the added panel weight, and confirms whether a deeper molded panel or a pultruded profile better suits the condition. Any upgrade outside the rated molded range goes to engineer review.

  • 38 mm. The shallower molded section under comparison, reviewed against the duty at the planned span.
  • 50 mm. The deeper molded section considered where the 38 mm panel is marginal or the duty is heavier.
  • deeper section. The added bar depth that brings more bending stiffness and a firmer walking surface.
  • span. The planned support spacing the section must span, read against the tabulated rows.
  • heavier duty. Heavier pedestrian traffic, staged tools or equipment that push the deck toward a deeper panel.

2. Worked Example and Site Checklist

Compare the verified molded rows for the weight move. The 38 mm molded panel is about 19.5 kg/m² at 68% open area; the 50 mm panel is about 27.0 kg/m² at 60% open area, a rise of roughly 7.5 kg/m². In imperial terms the 50 mm figure converts to about 5.53 lb/ft² (27.0 × 0.2048).

At a 1200 mm span the 38 mm molded row allows 6.5 kN/m²; if the design duty sits near that figure or deflection feels marginal, the 50 mm section may be considered within its own tabulated range. Spans or loads beyond the molded rows are not closed by adding depth; those need a separate structural check.

Check on siteWhat to recordWhy it matters
Compare duty against the 38 mm rowRecord the allowable at the planned spanThe upgrade case starts where the shallower section is marginal.
Consider 50 mm for a marginal rowNote where 38 mm sits close to or below dutyA deeper panel adds stiffness within its rated range.
Account for tools and equipmentList staged tools, carts or heavier foot trafficHeavier use can justify the deeper section before install.
Check the added weightCopy the kg/m² change for framing and liftingA deeper panel raises dead load and handling effort.
Review out-of-range upgradesFlag spans or duty beyond the molded rowsDepth cannot close a gap outside the rated range.
ItemVerified figure / note
Molded 38 mm19.5 kg/m² · 68% open area
Molded 50 mm27.0 kg/m² · 60% open area
Weight increase 38→50About 7.5 kg/m²
Molded 38 mm @ 1200 mm6.5 kN/m² allowable UDL

3. Failure Modes and Cautions

An unjustified upgrade picks the 50 mm panel before the actual duty or span is defined. The extra weight and cost load the framing without a matching need; where the real condition is a short light walkway, the deeper section is over-specification.

Another shortfall treats added depth as the answer for every marginal case. For long spans or heavy platform duty a pultruded T-bar or I-bar may suit better than a deeper molded panel; staying within molded depth can leave the deck under-stiffened for that duty.

  • Define the actual duty and span before upgrading; do not default to the deeper section.
  • Check panel weight against the framing and lifting plan when depth increases.
  • Compare profile family as well as depth; molded may not be the right series for long heavy decks.

4. Boundary: When This Does Not Apply

This upgrade discussion applies to molded selection within the tabulated uniform-load range. It does not cover concentrated point or wheel loads, cantilever projections, impact, fatigue life, snow load, uplift fixing, or temperature derating; those go to an independent structural assessment.

A 50 mm panel should not be assumed to cover spans or loads beyond its tabulated molded range; consider the pultruded series and have the engineer confirm against a matched report. Resin grade and chemical resistance are separate checks and are not inferred from the deeper section.

5. Frequently Asked Questions

When does 38 mm molded fall short?

When its allowable load at the planned span sits close to or below the design duty, or where deflection feels marginal, a deeper 50 mm section may be considered.

What does 50 mm molded weigh?

The verified 50 mm molded section is about 27.0 kg/m² with a 60% open area, per the data sheet; confirm exact mesh and resin on the drawing.

Is a deeper panel always the right upgrade?

Not always. For long spans or heavy platform duty a pultruded I-bar may suit better than a deeper molded panel; compare profile type as well as depth.

Should I upgrade before knowing the equipment load?

No. Define the actual duty and span first; an unneeded upgrade adds weight and cost. If duty is uncertain, flag it for engineer review.

Can the 50 mm section cover longer spans?

Only within its tabulated span range. Spans or loads outside the table need a separate structural check rather than an assumed deeper-section rating.

ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026 |Category: Structural Sizing |Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating Surface Selection | R13
📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]