/>

Calculating Open Area and Drainage From Pitch and Bar Width

Structural Mechanics
Direct Answer

Open area is the fraction of the panel face left as openings between bars; it follows the mesh pitch and the width of the bars themselves, and it sets the starting point for judging drainage.

  • Read pitch and bar width from the panel datasheet before estimating open area.
  • Compute the opening fraction, then relate it to the expected water passage.
  • Open area supports drainage judgment but does not by itself prove hydraulic capacity.

1. What Open Area Measures in a Grating Panel

Open area describes how much of the panel face is void between the load-carrying bars and transverse members. A higher opening fraction lets water, debris and light pass through more readily, while a denser mesh with wider bars covers more of the surface and carries more material across the panel.

The figure is a geometric property of the chosen mesh, not a measure of strength. Two panels can share the same bar depth yet differ in open area because their pitch and bar width differ; the stiffness and the drainage behavior are judged separately.

  • open area. the percentage of the panel face left as openings between bars and transverse members.
  • pitch. the center-to-center spacing between adjacent bars in one direction of the mesh.
  • bar width. the face width of a load-carrying bar, measured perpendicular to its depth.
  • opening fraction. the void proportion of the panel face, expressed as a decimal before converting to percent.
  • drainage passage. the route water takes through the openings rather than pooling on the surface.

2. Computing Open Area From Pitch and Bar Width

For a square molded grid with pitch p in both directions and bar width b, the solid fraction along one bar line is b/p. Accounting for both directions, the opening fraction is O = 1 − 2(b/p) + (b/p)², and the open-area percentage is 100 × O. The expression subtracts the two bar directions once and adds back their overlap so it is not counted twice.

For pultruded panels, where the main bars and cross-rods have different widths, the same principle applies using the actual spacing and width of each member type. Values should be read from the datasheet for the chosen profile; illustrative bar widths in a worked example are not a substitute for that specification.

  • Record pitch and bar width for each direction of the panel.
  • Apply the opening-fraction formula and convert to a percentage.
  • Compare the result against the drainage and coverage needs of the location.

3. Worked Example: Two Common Mesh Sizes

For a 38 mm pitch molded panel with an illustrative bar width b = 6 mm, b/p = 6/38 ≈ 0.158. The opening fraction is 1 − 2(0.158) + (0.158)² ≈ 1 − 0.316 + 0.025 ≈ 0.709, or about 70.9% open area. For a 19 mm mini-mesh with b = 4 mm, b/p = 4/19 ≈ 0.211; the opening fraction is 1 − 0.421 + 0.044 ≈ 0.623, or about 62.3%. These figures are geometric illustrations; confirm bar width against the datasheet.

MeshPitch pBar width bOpening fraction OOpen area
Molded 38×3838 mm6 mm (illustrative)≈ 0.709≈ 70.9%
Mini-mesh 19×1919 mm4 mm (illustrative)≈ 0.623≈ 62.3%
Pultruded profilePer datasheetPer datasheetComputed per memberPer datasheet
Formula termMeaning
O = 1 − 2(b/p) + (b/p)²Opening fraction for a square two-direction grid
100 × OOpen-area percentage
b/pSolid fraction along one bar line

4. Open Area, Drainage and Design Checks

A generous open area helps rain, washdown water and small debris pass through instead of pooling on the bars. It does not by itself state how much water the deck can carry: drainage also depends on slope, opening size, clogging by sediment or ice, and the capacity of the channels below. Those hydraulic conditions follow the site design rather than the mesh percentage alone.

Where fine objects, footwear or wheels must not fall through, the clear opening size matters as well as the total open area. A panel chosen for drainage should be checked against the objects and traffic expected on the surface, and against any local requirement for opening dimensions.

  • Note expected washdown, rainfall and any sediment or ice that could reduce passage.
  • Check clear opening size against objects and footwear that must stay above the mesh.
  • Treat the open-area figure as one input to the drainage review, not the whole hydraulic case.

5. Boundary and Review Notes

This note covers geometric open-area calculation and its relation to surface passage. It does not establish hydraulic capacity, slip resistance, load rating, fall-through protection compliance or chemical compatibility; those follow separate design checks and the applicable standards.

A panel selected for one drainage condition should not be assumed suitable for a heavier washdown duty or a finer object requirement without re-checking the opening size and area. Where the site hydrology changes, the mesh choice is reviewed again against the new water condition.

6. Frequently Asked Questions

How is open area percentage calculated?

From pitch p and bar width b: opening fraction O = 1 − 2(b/p) + (b/p)², then open area = 100 × O; read p and b from the panel datasheet.

Does a higher open area mean better drainage?

It helps water pass through, but drainage also depends on slope, opening size, clogging and the channels below; open area alone does not prove hydraulic capacity.

Why do two panels of the same depth differ in open area?

Because pitch and bar width differ; open area is a mesh geometry property, separate from the bar depth that governs stiffness.

What opening detail matters for fall-through safety?

The clear opening size, not only the total open area, must be checked against objects, footwear and wheels expected on the surface.

Where do I confirm the actual bar width and pitch?

Check the chosen spec series or datasheet for the profile; illustrative widths in a worked example are not a substitute for that specification.

ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026 |Category: Structural Mechanics |Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating Surface Selection | R13
📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]