/>

Reading Grating Terms: Bar Depth, Pitch and Profile Across Standards

Standards Comparison
Direct Answer

Grating terms differ between regional standards and supplier literature, so matching bar depth, pitch and profile across a drawing and specification prevents the wrong section being ordered.

  • Map the terms used on the drawing, spec and datasheet to a common meaning.
  • Distinguish bar depth, pitch, panel size and profile family when describing a section.
  • Confirm each definition against the adopted standard before finalizing the order.

1. Why the Same Panel Carries Different Names

Regional structural documents, supplier catalogues and project specifications may describe a composite panel using slightly different words for the same feature. One source's bar height, another's bar depth and a third's section depth can refer to the same vertical dimension of the load-carrying bar. Reading past the labels to the measured feature avoids confusion in selection.

A specification that lists only a product family without the measured depth, pitch and profile leaves room for the wrong section. The useful description ties each term to a dimension or feature: how deep the bar is, how far apart the bars run, and whether the panel is interwoven molded or continuous pultruded.

  • bar depth. the vertical height of a load-carrying bar; also called bar height in some sources.
  • pitch. center-to-center spacing between adjacent bars in one direction of the mesh.
  • profile. the cross-section shape of a bar, such as I-bar, T-bar or a molded interwoven section.
  • molded panel. a panel formed by interweaving and curing rovings into a square mesh grid.
  • pultruded panel. a panel built from continuous profiled bars tied with transverse rods or profiles.

2. Core Terms and Their Practical Meaning

Bar depth sets the panel's stiffness and span behavior; deeper bars generally resist sag over longer supports. Pitch controls the number of bars across the panel, the open area and the clear opening between members. Profile describes how the bar material is shaped, which affects bending stiffness and shear area differently across families.

Panel size, bearing length and surface finish are separate terms from bar depth and pitch. A deck can specify a 38 mm deep panel on a 38 mm pitch with a particular surface; mixing these dimensions in one description risks ordering a section that matches one figure but misses another requirement.

TermPractical meaningWhere it appears
Bar depth / heightVertical bar dimension driving stiffnessDatasheet, spec, section description
PitchCenter-to-center bar spacingMesh size, open area specification
ProfileBar cross-section shapeFamily selection: molded, I-bar, T-bar
Open areaVoid fraction of the panel faceDrainage and coverage requirement
Bearing lengthBar end resting on the supportInstallation and detailing notes

3. Mapping Molded and Pultruded Naming

Molded panels are described by their interwoven grid, often named by bar depth and mesh pitch; pultruded panels are described by their continuous profile family, such as I-bar or T-bar, together with depth and spacing. A comparison between families should state both the profile type and the measured dimensions rather than relying on a family label alone.

Some sources refer to the transverse members as rods, ties or cross-bars; others name the direction of span or the panel orientation differently. When moving a design between documents, identify which bars carry the spanning load and confirm the direction the pitch applies to.

  • State profile family, bar depth and pitch together in the section description.
  • Identify the spanning direction and the bars that carry load.
  • Align transverse member naming between drawing and datasheet.

4. Term Checkpoints on Drawings and Specs

Before an order is finalized, check that the drawing, specification and datasheet agree on bar depth, pitch, profile, panel size, open area and bearing details. Any term used loosely in one document should be tied to a measured dimension so the reviewer can verify the intended section.

CheckpointVerification
Bar depthMatches the datasheet section dimension
PitchSpacing in the spanning and transverse directions confirmed
ProfileFamily and bar shape match the requirement
Panel sizeCut and standard dimensions agree with the layout
Open areaMatches drainage or coverage need

Where a project references a regional standard, the definitions in that document govern how the terms are read. If a supplier name and a standard term do not line up, map them explicitly in the spec rather than assuming the label carries the same meaning.

5. Boundary: Confirm Definitions Against the Adopted Standard

This note helps align common grating terms across references. It does not define the standard's official requirements, certify compliance, or replace the project's adopted specification and its dimensional acceptance criteria.

When a drawing or spec uses a non-standard label, the underlying dimension and profile should be confirmed against the adopted document. Where terminology differs between suppliers, the order should restate the measured depth, pitch and profile to avoid a section mismatch.

6. Frequently Asked Questions

What is the difference between bar depth and pitch?

Bar depth is the vertical height of the spanning bar; pitch is the center-to-center spacing between adjacent bars. They describe different dimensions and both are stated in a section.

How are molded and pultruded panels named?

Molded panels are described by interwoven grid depth and mesh pitch; pultruded panels by continuous profile family such as I-bar or T-bar, with depth and spacing.

Why do standards use different grating terms?

Regional documents and catalogues label the same feature differently; reading to the measured dimension rather than the label prevents ordering the wrong section.

Which terms must agree on drawing and spec?

Bar depth, pitch, profile, panel size, open area and bearing details should match between the drawing, specification and datasheet.

What governs a term's official definition?

The adopted project or regional standard governs; map any supplier label to that definition explicitly rather than assuming the names are equivalent.

ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026 |Category: Standards Comparison |Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating Surface Selection | R13
📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]