Specify the molded or pultruded build-up to the bearer span, match the resin to the disinfectant/washing exposure, choose a damp-zone traction finish, seat over isolation bearings with the correct gaps, and close the RFQ with drawings and the matched documentation.
- Disinfectant and mopping water point to isophthalic polyester as the starting matrix; a stronger biocide, peroxide or concentrated cleaner reaching the deck moves the choice toward vinyl ester. The actual agent, its concentration and the temperature at the deck belong in the brief so the grade can be read against the resistance reference rather than a generic hygiene label.
- Molded sections suit the corridor and drain-edge pieces shaped around walls and penetrations; pultruded I-bar follows longer bearer runs where the support spacing demands a directional section. How often a panel lifts out for below-floor reach, and how many cut-outs the route carries, steer that mix.
- Concave dished panels shed collected wash water along damp stretches; grit top is added where operators stand during cleaning or maintenance. Smooth mesh stays in dry, sheltered points, and the opening should match the footwear and shoe covers used on site.
How this article differs: This page covers the pharmaceutical cleanroom corridor duty and procurement inputs; it does not re-derive load tables, concentrated-load checks or resin chemistry, which are handled in the dedicated reference articles.
1. Site Conditions and Duty
Process corridors, changing-airlock approaches and utility decks beside filling lines carry operators in shoe covers and occasional maintenance technicians. Floors are mopped on a schedule and wiped with the facility's chosen disinfectant, and humidity is held in a controlled band; the deck therefore sees repeated damp cleaning rather than immersion. Steel grating in these routes develops rust staining at bar edges and bearing points, and oxide particles can shed onto a clean workflow; aluminium can pit where disinfectant films sit. Composite panels walk dry underfoot, do not rust, and can be cut to line up with drains and service trenches without introducing a shedding metal substrate.
The usual traffic is walking personnel, not wheeled plant. Panels must give a stable route between process rooms and leave cleanable corners where they meet walls, curbs and drain edges. Where a panel lifts out for reach below the floor, its fit around a penetration or trench frame matters as much as its strength; corners against walls are the spots where residue and shoe-cover dirt accumulate most.
Contact is dilute disinfectant and washing water, not a concentrated reagent. Zones that stay damp after mopping take a different traction finish from sheltered ledges, and that split should be marked on the layout drawing instead of left to site choice. Any claim about product contact suitability for the facility's process must be supported by separate verified evidence; this page does not make such a claim.
Cleanability drives the detail here: bars should leave drains free of trapped residue, edge seals should resist the repeated wipe-down, and removable sections should lift without disturbing the neighbouring panels' bearing. Gowning bends, airlock thresholds and utility skid fronts are the standing points where a polished or loose surface would be felt first.
2. Build-up, Resin and Surface Selection
| Route / zone | Cleanliness risk | Duty served | Suggested panel | Resin & finish note |
|---|---|---|---|---|
| Process corridor | Damp mopping, disinfectant wipes | Operator walking route between rooms | Molded 38 mm 38×38 | Iso baseline; concave where damp |
| Airlock / changing approach | Controlled humidity, shoe-cover traffic | Access to gowning and air lock | Molded 38 mm 50×50 | Matched resin; smooth dry sheltered points |
| Utility washable deck | Repeated washdown, spill wipes | Reach beside filling and packaging skids | Pultruded 38 mm I-bar | Resin per recorded biocide |
| Removable trench panel | Local dampness, lift-out duty | Access below floor line | Molded 38 mm cut-to-size | Sealed cut edge with matched resin |
- Disinfectant and mopping water point to isophthalic polyester as the starting matrix; a stronger biocide, peroxide or concentrated cleaner reaching the deck moves the choice toward vinyl ester. The actual agent, its concentration and the temperature at the deck belong in the brief so the grade can be read against the resistance reference rather than a generic hygiene label.
- Molded sections suit the corridor and drain-edge pieces shaped around walls and penetrations; pultruded I-bar follows longer bearer runs where the support spacing demands a directional section. How often a panel lifts out for below-floor reach, and how many cut-outs the route carries, steer that mix.
- Concave dished panels shed collected wash water along damp stretches; grit top is added where operators stand during cleaning or maintenance. Smooth mesh stays in dry, sheltered points, and the opening should match the footwear and shoe covers used on site.
- Checking a molded 38 mm 38×38 panel over a 600 mm bearer span at L/200: the matched table lists about 25 kN/m² as an indicative uniform walking load. The check assumes a single simply supported bay under evenly distributed pedestrian traffic over a flat, sound bearing; it does not state a point, wheel or concentrated capacity, and the matched report governs final sizing.
3. Installation and Bearing Details
- Before seating panels, walk the floor frame and bearers for free soil and consistent bearing width; corners where the frame twists are the places a panel will rock on.
- Keep lift-out panels aligned to the trench frame so they rest squarely on the ledge; when a cover is removed for service, neighbouring sections should not have to be prised aside.
- After the first cleaning cycles, revisit bearing contact and panel position to catch any shift caused by damp mopping or floor washdown.
- ≥ 50 mm bearing on steel/FRP support; 60 mm preferred at end spans
- 3 mm neoprene strip on steel supports to cut galvanic contact and local stress
- 10–15 mm end gap for thermal movement (~20 mm at long runs)
- 6–10 mm side gap for expansion and safe lifting
- Clips at every support and every corner; C/L/T/W/saddle families; A2-70 M6/M8 bolts
- Hand-tighten plus 1/4 turn; do not over-torque
- Seal any cut edge with matched resin within 24 hours
- Walk the deck and re-torque after 2 weeks of service
4. Routine Inspection and Maintenance
| Task | Frequency | What to check |
|---|---|---|
| Visual inspection | Monthly | Cracked bars, loose clips, edge seal, displaced panels |
| Clip torque check | Quarterly, first year | Hand-tight; re-torque any loose fixing |
| Washdown | As needed | Fresh water, low pressure; no acid or solvent-based cleaner |
| Grit top renewal | As needed | Top up worn traction with matched gritted resin |
| Edge seal check | Annually | Touch up any bare roving before it spreads |
| UV top-coat | Every 3–5 years | Re-coat exposed surface with matched resin on request |
- Watch standing pads at cleaning points for polished traction or dull bloom where disinfectant film concentrates; a panel that feels swollen should be noted for resin review.
- Residue that collects between bars can be lifted with low-pressure fresh water; unlisted acid or solvent products stay off the resin matrix unless the matched note permits them. Edge seals near drains get an annual touch-up before bare roving spreads along the route.
5. RFQ Inputs and Procurement Checklist
- Name the disinfectant or cleaning agent, its recorded concentration and the operating temperature at deck level.
- Give corridor length and width, bearer spacing, and whether the route serves walking rounds, standing work or occasional equipment reach.
- Attach the frame plan showing bearers, walls, penetrations and lift-out panels, with finishes split between damp pads and dry sheltered points.
- Governing access standard and project deflection limit are cited with the order.
- Matched resistance note confirms the resin grade against the recorded medium.
- Batch material record and Barcol hardness check accompany the delivered panels.
- Any point, wheel, concentrated or equipment load is referred to engineer review and the matched report.
| Minimum order (MOQ) | 10 m² |
| Standard production | 15–25 working days after drawing approval |
| Overall lead time | 12–36 working days overall |
| Indicative price | USD 15–95/m² |
| Manufacturing history | Founded 2004; 200+ employees; 20,000+ m² plant |
| Export reach | 45+ countries; 541+ customer reviews, 4.9/5 average rating |
6. Compliance and Service Boundaries
7. Frequently Asked Questions
Which resin holds up around cleanroom decks?
Isophthalic polyester covers ordinary mopping water and disinfectant films; vinyl ester is reserved for stronger biocides, peroxide or concentrated cleaning contact. The grade is set against the recorded agent, concentration and temperature.
Molded or pultruded for a corridor?
Molded sections shape cleanly around walls, drains and penetrations; pultruded I-bar follows longer bearer spans with a lighter directional section. The measured support spacing and lift-out frequency decide the mix.
What finish stops slipping after damp mopping?
Concave dished panels shed collected water on damp stretches; grit-embedded top adds grip where operators stand during cleaning. Keep smooth mesh for dry, sheltered points and match the opening to site shoe covers.
How are panels seated over the cleanroom frame?
Sections bear over the isolation strip on steel, with end and side clearances per the node drawing; lift-out hardware stays accessible, and fixings are hand-tightened to setting rather than over-driven.
How often should cleanroom grating be inspected?
Monthly visual rounds catch cracked bars and loose clips early; clip torque is reviewed quarterly in year one, with an annual edge-seal check and periodic top-coat renewal on exposed routes.
