Specify the molded or pultruded build-up to the deck span, verify resin compatibility against the recorded coating chemicals, choose a prep-zone traction finish, seat over isolation bearings with the correct gaps, and close the RFQ with drawings and the matched documentation.
- Check compatibility thinner by thinner and reducer by reducer against the recorded vapour phase; aromatic or ketone media narrow the family, and anything unlisted in the reference needs test evidence rather than a generic approval. Product strength and deck temperature go into the brief.
- Broad prep decks cut around fixturing and drains take molded 38 mm; longer narrow sump-edge runs carry pultruded T-bar. Opening layout and measured span steer the mix.
- Grit tops cover standing prep pads; dished concave faces shed runoff off the drain ledges. The opening passes overspray and residue without trapping buildup and keeps fittings above the sump.
How this article differs: This page covers the paint prep area duty and procurement inputs; it does not re-derive load tables, concentrated-load checks or resin chemistry, which are handled in the dedicated reference articles.
1. Site Conditions and Duty
Spray booth prep areas and overspray decks carry operators around parts being masked, wiped and coated, with coating residue, overspray dust and solvent vapour settling on the deck. Grating over drain slots and sump openings lets residue and cleaning runoff pass through while giving a standing surface; steel floors in these zones stain and corrode where solvent films and residue sit, and composite sections resist the rust and corrosion that steel shows in these films.
Preparers walk with tools and light material; vehicles do not enter these decks. Decks clear part fixturing, drain slots and sump edges, leaving standing points at each work position. Bearer spacing sets span and deflection; a part or fixture set down on the deck goes to separate structural review.
Coating residue, solvent vapour and cleaning runoff are the contacts, not continuous solvent immersion. Compatibility is checked against each recorded thinner and reducer; aromatic or ketone products can limit the resin choice, and an unlisted medium needs test evidence before selection. The finish sheds runoff and resists trapping overspray between bars.
Masking benches, booth fronts and sump edges are the residue spots; vapour films concentrate where parts stand between coats. Cut edges around fixture penetrations need a sealed roving face, and the aperture should keep fittings and small masks above the sump below. Replacement masks and spray consumables are staged on the prep pad rather than on the bar opening, and that staging spot should be marked on the layout. The heaviest use hits each booth fixture point; overspray dust settles nearest the sump edge, where packed residue would bridge the bars, and a consumable cart rests on the adjacent prep pad, off the opening.
2. Build-up, Resin and Surface Selection
| Deck zone | Residue source | Work point | Panel option | Resin / finish |
|---|---|---|---|---|
| Prep standing deck | Overspray residue, vapour | Operator work at part | Molded 38 mm 50×50 | Compatibility checked; grit |
| Booth drain slot | Cleaning runoff, damp film | Walking over drain opening | Molded 38 mm 38×38 | Matched resin; concave |
| Sump edge platform | Intermittent spill, vapour | Reach sump and drains | Pultruded 38 mm T-bar | Resin to recorded medium |
| Removable drain section | Local dampness, lift-out duty | Lift panel for sump reach | Molded 38 mm cut-to-size | Sealed edge; matched resin |
- Check compatibility thinner by thinner and reducer by reducer against the recorded vapour phase; aromatic or ketone media narrow the family, and anything unlisted in the reference needs test evidence rather than a generic approval. Product strength and deck temperature go into the brief.
- Broad prep decks cut around fixturing and drains take molded 38 mm; longer narrow sump-edge runs carry pultruded T-bar. Opening layout and measured span steer the mix.
- Grit tops cover standing prep pads; dished concave faces shed runoff off the drain ledges. The opening passes overspray and residue without trapping buildup and keeps fittings above the sump.
- Read a molded 38 mm 38×38 panel over 600 mm bearers; under an L/200 check the reference table corresponds to about 25 kN/m² of uniform walking load. The figure assumes preparers standing and walking on a single simply supported bay over a clean level bearing; staged parts or fixtures are outside this check and go through the matched report in structural review.
3. Installation and Bearing Details
- Before laying sections, scrub overspray buildup off the prep bearers; dried coating on the support line prevents a flat seat under booth traffic.
- Set the more-open panels over sump and drain openings so residue washes through, and keep prep pads aligned with each part fixturing point.
- ≥ 50 mm bearing on steel/FRP support; 60 mm preferred at end spans
- 3 mm neoprene strip on steel supports to cut galvanic contact and local stress
- 10–15 mm end gap for thermal movement (~20 mm at long runs)
- 6–10 mm side gap for expansion and safe lifting
- Clips at every support and every corner; C/L/T/W/saddle families; A2-70 M6/M8 bolts
- Hand-tighten plus 1/4 turn; do not over-torque
- Seal any cut edge with matched resin within 24 hours
- Walk the deck and re-torque after 2 weeks of service
4. Routine Inspection and Maintenance
| Task | Frequency | What to check |
|---|---|---|
| Visual inspection | Monthly | Cracked bars, loose clips, edge seal, displaced panels |
| Clip torque check | Quarterly, first year | Hand-tight; re-torque any loose fixing |
| Washdown | As needed | Fresh water, low pressure; no acid or solvent-based cleaner |
| Grit top renewal | As needed | Top up worn traction with matched gritted resin |
| Edge seal check | Annually | Touch up any bare roving before it spreads |
| UV top-coat | Every 3–5 years | Re-coat exposed surface with matched resin on request |
- Trace the booth round for residue packed in the aperture near sumps, and inspect standing pads for a softening haze where thinner films have concentrated; a swollen section should be flagged to resin review.
- Run cleanup through the mesh with low-pressure water and a permitted cleaner; hold any thinner, reducer or ketone off the laminate unless the resin register for that formulation allows it.
5. RFQ Inputs and Procurement Checklist
- Name every thinner, reducer, coating and cleaning agent contacting the floor, with aromatic or ketone content and deck temperature.
- Give the prep deck length and width, bearer centres, and the split between standing part work, drain crossing and sump reach.
- Send the booth sketch with fixturing, drains, sumps and lift-out panels marked, separating standing prep pads from drain ledges.
- Governing access standard and project deflection limit are cited with the order.
- Matched resistance note confirms the resin grade against the recorded medium.
- Batch material record and Barcol hardness check accompany the delivered panels.
- Any point, wheel, concentrated or equipment load is referred to engineer review and the matched report.
| Minimum order (MOQ) | 10 m² |
| Standard production | 15–25 working days after drawing approval |
| Overall lead time | 12–36 working days overall |
| Indicative price | USD 15–95/m² |
| Manufacturing history | Founded 2004; 200+ employees; 20,000+ m² plant |
| Export reach | 45+ countries; 541+ customer reviews, 4.9/5 average rating |
6. Compliance and Service Boundaries
7. Frequently Asked Questions
Which resin suits a paint prep deck?
Compatibility is checked against each recorded thinner, reducer and cleaning agent, including aromatic or ketone content; unlisted media need test evidence before selection rather than a generic approval.
Molded or pultruded over a booth drain?
Molded sections suit broad prep decks cut around fixturing and drains; pultruded T-bar spans longer narrow sump-edge runs. The measured span and opening layout decide the mix.
What finish handles overspray and runoff?
Embedded grit grips standing prep pads; concave dished faces shed runoff on ledges; open mesh lets overspray and residue pass through without trapping buildup between bars.
How are prep deck panels fixed?
Fixings matched to the deck family seat bar to each bearer and corner over the isolation strip; end and side gaps follow the node drawing, and bolts are hand-tightened to setting.
How often should booth deck grating be inspected?
Monthly rounds catch broken bar tops, loose clips and residue-packed mesh early; review clip torque quarterly in year one, watch pads for softening, and complete an annual edge-seal check.
