Grade the vinyl-ester matrix to the strongest dosing reagent, lay a draining coarse mesh over the bund, seal every frame penetration, map segregation and spill trays, and confirm drum or trolley use through factory review.
- Resin grade: vinyl ester is the starting point for a dosing skid that sees acid, caustic or bleach splash; epoxy is reserved for a more aggressive or higher-temperature reagent after resistance review. General isophthalic polyester is not selected where concentrated reagent pools, because it can soften or blister under that contact.
- Section choice: molded 38 mm serves the drum pad and bund floor cut around equipment; pultruded I-bar follows the pump approach runs. The coarser 50×50 mesh drains spillage quickly across the containment floor; span and walking load set the depth.
- Splash surface: grit top at hose-connection standing points for grip on a wet pad; concave dished members along the bund drain; avoid a covered solid finish that would hold spilled reagent on the deck.
How this article differs: This page covers dosing-area grating selection and procurement; it does not size the metering pumps, design the bund wall or neutralization system, or detail resin chemistry, which remain in the dedicated references.
1. Site Conditions and Duty
Dosing skids feed bleach, acid or caustic into the treatment train through metering pumps, injection quills and reagent drums; the floor and walkway around this equipment take reagent drips, hose-connection splash and the occasional small spill washed into the bund. Unlike a humid tank rim, this duty contacts concentrated or partially concentrated chemicals directly, so the resin matrix itself is the first line of defence. A general polyester that tolerates moisture can blister, soften or chalk where a reagent pools, and the damage often appears first at a drip point or spill edge rather than across the whole panel.
The zone splits into the skid approach where staff connect hoses, the containment floor under drums and pumps, and the bund drain route that carries wash water to the sump. Deck depth follows the walking and occasional carry load, but the resin grade follows the most aggressive reagent present, not the average wetness. Segregation between incompatible dosing lines, the spill tray under each pump and the eye-wash position should be readable on the layout before panels are quoted.
Spillage here is episodic: a small splash at connection, a washdown after a leak, then a return to damp vapour. The grating must shed liquid through the mesh to the bund drain rather than hold it on the surface, and any cut edge or drilled hole around the skid frame is a likely entry point for reagent, so sealing matters more than on a plain walkway.
2. Build-up, Resin and Surface Selection
| Dosing zone | Chemical exposure | Use | Section | Resin / containment note |
|---|---|---|---|---|
| Reagent drum pad | Bleach, acid or caustic drips | Stand at drum connection | Molded 38 mm 38×38 | Vinyl ester; sealed edges |
| Metering pump approach | Local splash, spill wash | Hose connection and service | Pultruded 38 mm I-bar | VE matrix; grit top |
| Bund containment floor | Episodic spill, wash water | Catch drips to sump | Molded 38 mm 50×50 | Resin per strongest reagent |
| Skid frame opening | Intermittent access | Removable section over pump | Molded 38 mm cut-to-size | Matched resin; drain route |
- Resin grade: vinyl ester is the starting point for a dosing skid that sees acid, caustic or bleach splash; epoxy is reserved for a more aggressive or higher-temperature reagent after resistance review. General isophthalic polyester is not selected where concentrated reagent pools, because it can soften or blister under that contact.
- Section choice: molded 38 mm serves the drum pad and bund floor cut around equipment; pultruded I-bar follows the pump approach runs. The coarser 50×50 mesh drains spillage quickly across the containment floor; span and walking load set the depth.
- Splash surface: grit top at hose-connection standing points for grip on a wet pad; concave dished members along the bund drain; avoid a covered solid finish that would hold spilled reagent on the deck.
- Worked example: a vinyl-ester molded 38 mm 38×38 panel over a 900 mm simply supported single span at L/200 lists about 12 kN/m² as an indicative uniform walking load. This distributed figure excludes spill weight, drum handling and any trolley; reagent compatibility is confirmed against the chemical resistance table, and the matched report governs the final span.
- Spill boundary: identify the strongest reagent, its concentration and temperature, and whether the floor sees a neat spill or a diluted wash; the resin choice and containment depth follow that record, not a generic corrosion label.
3. Installation and Bearing Details
- Map each dosing line and its reagent before laying panels; confirm incompatible products are segregated and that the bund drain routes wash water away from the skid.
- Bed sections on the isolation bedding over steel supports, keeping node end and side clearances around the skid frame, pump plinths and drum pads.
- Fix every support and corner with the stainless clip matched to the section; hand-tighten to setting, and keep removable pump sections free to lift for servicing.
- Seal all sawn edges, drilled holes and frame penetrations with matched resin within 24 hours; after any spill wash, check that the mesh drains and that no reagent film remains on a panel.
- ≥ 50 mm bearing on steel/FRP support; 60 mm preferred at end spans
- 3 mm neoprene strip on steel supports to cut galvanic contact and local stress
- 10–15 mm end gap for thermal movement (~20 mm at long runs)
- 6–10 mm side gap for expansion and safe lifting
- Clips at every support and every corner; C/L/T/W/saddle families; A2-70 M6/M8 bolts
- Hand-tighten plus 1/4 turn; do not over-torque
- Seal any cut edge with matched resin within 24 hours
- Walk the deck and re-torque after 2 weeks of service
4. Routine Inspection and Maintenance
| Task | Frequency | What to check |
|---|---|---|
| Visual inspection | Monthly | Cracked bars, loose clips, edge seal, displaced panels |
| Clip torque check | Quarterly, first year | Hand-tight; re-torque any loose fixing |
| Washdown | As needed | Fresh water, low pressure; no acid or solvent-based cleaner |
| Grit top renewal | As needed | Top up worn traction with matched gritted resin |
| Edge seal check | Annually | Touch up any bare roving before it spreads |
| UV top-coat | Every 3–5 years | Re-coat exposed surface with matched resin on request |
- Inspect drip points and spill edges for blistering, softening, chalky bloom or swollen resin; these are the first signs of a resin-grade mismatch.
- Check clips and removable sections under the skid for loosening from pump vibration, and look for cracked corners around drum pads.
- Flush spill residue to the bund sump with fresh water at low pressure; do not apply solvent or an incompatible cleaner to the matrix.
- Touch up bare fibre and worn grit at connection points; flag any panel showing matrix softening for resin-grade review rather than surface repair.
5. RFQ Inputs and Procurement Checklist
- List every reagent dosed nearby: product name, concentration, temperature and whether contact is neat splash or diluted wash.
- Give skid layout, drum and pump positions, bund dimensions, drain route and the expected access: connection visits, drum carry or occasional trolley.
- Mark splash pads, containment floor and sheltered skid corners with the finish wanted in each.
- Attach the dosing layout showing segregation, spill trays, eye-wash point, sump and removable sections.
- Cite the governing standard and deflection limit, and request the matched chemical resistance note, batch record and hardness check; confirm any drum or trolley handling with factory engineering review.
- Governing access standard and project deflection limit are cited with the order.
- Matched resistance note confirms the resin grade against the recorded medium.
- Batch material record and Barcol hardness check accompany the delivered panels.
- Any point, wheel, concentrated or equipment load is referred to engineer review and the matched report.
| Minimum order (MOQ) | 10 m² |
| Standard production | 15–25 working days after drawing approval |
| Overall lead time | 12–36 working days overall |
| Indicative price | USD 15–95/m² |
| Manufacturing history | Founded 2004; 200+ employees; 20,000+ m² plant |
| Export reach | 45+ countries; 541+ customer reviews, 4.9/5 average rating |
6. Compliance and Service Boundaries
7. Frequently Asked Questions
Which resin resists bleach, acid and caustic on a dosing floor?
Vinyl ester starts the grade for reagent splash; epoxy follows only for a more aggressive or hotter product after resistance review. General polyester is not used where concentrated reagent pools.
What damage shows the resin grade is wrong?
Blistering, softening, chalky bloom or swelling at a drip point or spill edge signals a matrix mismatch; such panels go to resin review, not just a top-coat repair.
How should a bund floor drain spilled reagent?
The mesh drains spillage and wash water toward the bund sump; a coarse 50×50 opening sheds liquid faster, and a solid covered finish that holds reagent on the deck is avoided.
Does the grating hold the drums or pumps?
No. Drums, pumps and their loads rest on the skid frame or plinth; the deck is the walking and spill-catching surface. Drum handling and trolley loads need engineer review.
What reagent details must the RFQ record?
Product, concentration, temperature and whether contact is neat splash or diluted wash, plus segregation and spill-tray positions; these set the resin grade and containment layout against the resistance table.
