📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Heavy Plant Platform

65 mm Pultruded I-bar FRP/GRP Grating, I-bar 65 mm HD Mesh, Grit Top for Heavy Plant Platform

65 mm HD pultruded I-bar FRP/GRP grating configured with a grit top for heavy plant platform. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typePultruded I-bar FRP/GRP grating
MeshI-bar 65 mm HD
Depth65 mm
Standard panel1220 x 3660 mm, cut to size
Open areaconfirm_with_factory
Unit weightconfirm_with_factory
Recommended resinIsophthalic polyester
SurfaceQuartz-grit anti-slip top
Bar orientationUnidirectional heavy pultruded profile; bar direction and support layout must be confirmed against the project load case.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm62 kN/m²
900 mm35 kN/m²
1200 mm20 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

Around heavy process equipment and modules where the platform sees oily or intermittently wet spillage, this 65 mm HD pultruded I-bar carries a raised maintenance platform beside heavy units with a bonded quartz-grit anti-slip top. The HD section is reserved for long or heavy duty; light pedestrian decks use a lighter profile, and wheel, point or cantilever loads outside the table need separate engineering review. The deep 65 mm HD profile limits deflection on heavy units and long unsupported runs. The grit top provides extra anti-slip margin on inclined and high-traffic exposed routes. Bearing points and clip positions are laid out before fixing; exposed cut edges are dressed afterward. Service access around the deck follows the approved layout; cut edges are dressed after confirmation.

Section profile and fixing

The 65 mm HD pultruded I-bar is the highest-stiffness section in this range, for long spans, heavy platforms and equipment decks where deflection under load must stay controlled. Heavy unidirectional profile; confirm bar direction and support layout against the project load case, space heavy-duty clips to the bearers, and check edge bearing on the HD frame.

Surface finish

A bonded quartz-grit layer raises slip resistance on ramps, stairs, busy outdoor steps and oily or intermittently wet treads. Ramps, stair treads, heavy-traffic platforms and exposed routes where extra anti-slip margin is required.

Data availability

For this 65 mm HD pultruded I-bar grit heavy plant platform, unit weight and open area are confirm_with_factory pending the factory return. Once the figures arrive they set the deck self-weight used in support design and the ventilation or drainage passage; until then the verified UDL table remains the selection basis.

Resin selection

Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • heavy plant platform
  • pultruded i-bar heavy plant platform
  • grit-top heavy plant platform
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 65 mm HD pultruded I-bar grit grating for heavy plant platform carry at a 900 mm span?

Which resin suits the heavy plant platform on this 65 mm HD pultruded I-bar grit grating?

Is the quartz-grit anti-slip top surface suitable for the 65 mm HD pultruded I-bar grating for heavy plant platform?

How are these 65 mm HD pultruded I-bar grit panels for heavy plant platform fixed to the supports?

What panel size, MOQ and lead time apply to the 65 mm HD pultruded I-bar grit grating for heavy plant platform?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]