FRP/GRP Grating Specification · Oil And Gas Facility Deck
65 mm Pultruded I-bar FRP/GRP Grating, I-bar 65 mm HD Mesh, Concave Top for Oil And Gas Facility Deck
65 mm HD pultruded I-bar FRP/GRP grating configured with a concave top for oil and gas facility deck. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.
Specification
| Product type | Pultruded I-bar FRP/GRP grating |
|---|---|
| Mesh | I-bar 65 mm HD |
| Depth | 65 mm |
| Standard panel | 1220 x 3660 mm, cut to size |
| Open area | confirm_with_factory |
| Unit weight | confirm_with_factory |
| Recommended resin | Isophthalic polyester; vinyl ester where stronger attack is confirmed in writing |
| Surface | Concave (meniscus) top |
| Bar orientation | Unidirectional heavy pultruded profile; bar direction and support layout must be confirmed against the project load case. |
Allowable uniform load by support span
| Support span | Allowable UDL (kN/m²) |
|---|---|
| 600 mm | 62 kN/m² |
| 900 mm | 35 kN/m² |
| 1200 mm | 20 kN/m² |
Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.
Selection rationale
On the longest process walkways and heavy equipment platforms in oil and gas facilities, this 65 mm HD pultruded I-bar handles a hydrocarbon atmosphere, local chemical traces and outdoor weather where the highest stiffness is required. The section is reserved for long or heavy decks; routine light access should use a lighter profile, and special zoning or any load beyond the verified table is confirmed by written engineering review. The deep 65 mm HD profile limits deflection on heavy units and long unsupported runs. The concave meniscus crown drains water off the contact patch and grips damp footwear without added grit. Support bearing and clip spacing follow the approved layout; edges are checked for even contact. The panel is laid to the section direction; upkeep follows the care guidance for the chosen top.
Section profile and fixing
The 65 mm HD pultruded I-bar is the highest-stiffness section in this range, for long spans, heavy platforms and equipment decks where deflection under load must stay controlled. Heavy unidirectional profile; confirm bar direction and support layout against the project load case, space heavy-duty clips to the bearers, and check edge bearing on the HD frame.
Surface finish
The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.
Data availability
Weight per square metre and open mesh percentage for the 65 mm HD pultruded I-bar concave oil and gas facility deck are not in the verified matrix and must be confirmed with the factory. Supplying them unlocks the self-weight check for bearer design and the passage-area calculation; the listed UDL values still guide the initial choice.
Resin selection
Isophthalic polyester; vinyl ester where stronger attack is confirmed in writing. Isophthalic polyester is the starting point; vinyl ester is substituted where the specific ore, brine or chemical stream warrants it, confirmed in writing.
Vinyl ester is substituted where the specific ore, brine or chemical stream warrants it, after written confirmation. Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.
Installation, fixing and delivery
Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.
Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.
Request-for-quotation inputs
- Overall dimensions and required panel layout
- Support spacing / clear span and beam layout
- Design load: uniform, wheel or point load, and expected use
- Resin requirement and contact medium, concentration and temperature
- Surface finish (concave, grit or smooth)
- Quantity in square metres
- Destination country and any local standard to follow
Typical uses
- oil and gas facility deck
- pultruded i-bar oil and gas facility deck
- concave-top oil and gas facility deck
- industrial personnel walkway
- corrosion-resistant platform deck
- open-mesh drainage and ventilation deck
