FRP/GRP Grating Specification · Equipment Support Deck
65 mm Pultruded I-bar FRP/GRP Grating, I-bar 65 mm HD Mesh, Concave Top for Equipment Support Deck
65 mm HD pultruded I-bar FRP/GRP grating configured with a concave top for equipment support deck. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.
Specification
| Product type | Pultruded I-bar FRP/GRP grating |
|---|---|
| Mesh | I-bar 65 mm HD |
| Depth | 65 mm |
| Standard panel | 1220 x 3660 mm, cut to size |
| Open area | confirm_with_factory |
| Unit weight | confirm_with_factory |
| Recommended resin | Isophthalic polyester |
| Surface | Concave (meniscus) top |
| Bar orientation | Unidirectional heavy pultruded profile; bar direction and support layout must be confirmed against the project load case. |
Allowable uniform load by support span
| Support span | Allowable UDL (kN/m²) |
|---|---|
| 600 mm | 62 kN/m² |
| 900 mm | 35 kN/m² |
| 1200 mm | 20 kN/m² |
Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.
Selection rationale
Above or beside heavy packaged units and modules, the 65 mm HD pultruded I-bar keeps deflection controlled on a static equipment platform where crews service larger machinery. The deep HD profile targets long bearer runs and heavier unit footings instead of short light footpaths. The concave face channels water away from the walking line without an added grit layer. Bearing points and clip positions are laid out before fixing, and cutout edges are finished once positions are confirmed.
Section profile and fixing
The 65 mm HD pultruded I-bar is the highest-stiffness section in this range, for long spans, heavy platforms and equipment decks where deflection under load must stay controlled. Heavy unidirectional profile; confirm bar direction and support layout against the project load case, space heavy-duty clips to the bearers, and check edge bearing on the HD frame.
Surface finish
The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.
Data availability
The factory must confirm two fields for the 65 mm HD pultruded I-bar concave equipment support deck: deck unit weight and open-area percentage. Those confirmed numbers feed the support self-weight design and the airflow or water passage sizing; the verified span loads are the interim reference while the reply is awaited.
Resin selection
Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.
Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.
Installation, fixing and delivery
Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.
Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.
Request-for-quotation inputs
- Overall dimensions and required panel layout
- Support spacing / clear span and beam layout
- Design load: uniform, wheel or point load, and expected use
- Resin requirement and contact medium, concentration and temperature
- Surface finish (concave, grit or smooth)
- Quantity in square metres
- Destination country and any local standard to follow
Typical uses
- equipment support deck
- pultruded i-bar equipment support deck
- concave-top equipment support deck
- industrial personnel walkway
- corrosion-resistant platform deck
- open-mesh drainage and ventilation deck
