📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Cable Trench Cover

65 mm Pultruded I-bar FRP/GRP Grating, I-bar 65 mm HD Mesh, Concave Top for Cable Trench Cover

65 mm HD pultruded I-bar FRP/GRP grating configured with a concave top for cable trench cover. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typePultruded I-bar FRP/GRP grating
MeshI-bar 65 mm HD
Depth65 mm
Standard panel1220 x 3660 mm, cut to size
Open areaconfirm_with_factory
Unit weightconfirm_with_factory
Recommended resinIsophthalic polyester
SurfaceConcave (meniscus) top
Bar orientationUnidirectional heavy pultruded profile; bar direction and support layout must be confirmed against the project load case.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm62 kN/m²
900 mm35 kN/m²
1200 mm20 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

Over deep cable trenches and routed runs where a heavier cover is required, this 65 mm HD pultruded I-bar provides a stiff non-conductive, corrosion-resistant deck under light foot traffic and equipment access above the cables. The section is reserved for long or loaded crossings; light trench covers would use a lighter profile, and any concentrated cable-side load beyond the table is reviewed separately. The 65 mm HD section is reserved for long or heavy service and equipment decks. A meniscus-shaped top that sheds runoff and keeps wet-foot grip on drained outdoor routes. Panel direction, clips and edge bearing are checked to the frame drawing before fixing. Layout and fixing follow the support drawing; the finish is matched to the service condition described above.

Section profile and fixing

The 65 mm HD pultruded I-bar is the highest-stiffness section in this range, for long spans, heavy platforms and equipment decks where deflection under load must stay controlled. Heavy unidirectional profile; confirm bar direction and support layout against the project load case, space heavy-duty clips to the bearers, and check edge bearing on the HD frame.

Surface finish

The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.

Data availability

The factory must confirm two fields for the 65 mm HD pultruded I-bar concave cable trench cover: deck unit weight and open-area percentage. Those confirmed numbers feed the support self-weight design and the airflow or water passage sizing; the verified span loads are the interim reference while the reply is awaited.

Resin selection

Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • cable trench cover
  • pultruded i-bar cable trench cover
  • concave-top cable trench cover
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 65 mm HD pultruded I-bar concave grating for cable trench cover carry at a 900 mm span?

Which resin suits the cable trench cover on this 65 mm HD pultruded I-bar concave grating?

Is the concave (meniscus) top surface suitable for the 65 mm HD pultruded I-bar grating for cable trench cover?

How are these 65 mm HD pultruded I-bar concave panels for cable trench cover fixed to the supports?

What panel size, MOQ and lead time apply to the 65 mm HD pultruded I-bar concave grating for cable trench cover?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]