📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Heavy Plant Platform

50 mm Pultruded I-bar FRP/GRP Grating, I-bar 50 mm Mesh, Grit Top for Heavy Plant Platform

50 mm pultruded I-bar FRP/GRP grating configured with a grit top for heavy plant platform. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typePultruded I-bar FRP/GRP grating
MeshI-bar 50 mm
Depth50 mm
Standard panel1220 x 3660 mm, cut to size
Open areaconfirm_with_factory
Unit weightconfirm_with_factory
Recommended resinIsophthalic polyester
SurfaceQuartz-grit anti-slip top
Bar orientationUnidirectional pultruded profile; bars run parallel to the main load path between bearers.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm48 kN/m²
900 mm26 kN/m²
1200 mm14 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

raised platform around heavy process equipment, machinery bases and plant modules; maintenance access beside heavy units; local ambient exposure with occasional spill cleanup around the equipment

This 50 mm pultruded section is the heavy-duty choice for wider bearer spacing. Span-load figures below run 48 kN/m² (600 mm), 26 (900 mm) and 14 (1200 mm) on an L/200 simple span. Bearing spacing and any wheel, point or cantilever load are confirmed against the verified table before fixing.

The grit top provides extra anti-slip margin on inclined and high-traffic exposed routes. On site the panel follows the section direction; fixing clips and bearing are verified against the layout.

Cutouts and edges are finished after layout confirmation; the walking condition governs the finish choice.

Section profile and fixing

The 50 mm pultruded I-bar is a heavy-duty section for wider support spacing, plant access decks and repeated rolling loads around packaged equipment. Unidirectional bars run parallel to the main load path; fix with rated clips to the support frame, check bar direction against the wheel or foot load, and finish cut openings by the factory.

Surface finish

A bonded quartz-grit layer raises slip resistance on ramps, stairs, busy outdoor steps and oily or intermittently wet treads. Ramps, stair treads, heavy-traffic platforms and exposed routes where extra anti-slip margin is required.

Data availability

Weight per square metre and open mesh percentage for the 50 mm pultruded I-bar grit heavy plant platform are not in the verified matrix and must be confirmed with the factory. Supplying them unlocks the self-weight check for bearer design and the passage-area calculation; the listed UDL values still guide the initial choice.

Resin selection

Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • heavy plant platform
  • pultruded i-bar heavy plant platform
  • grit-top heavy plant platform
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 50 mm pultruded I-bar grit grating for heavy plant platform carry at a 900 mm span?

Which resin suits the heavy plant platform on this 50 mm pultruded I-bar grit grating?

Is the quartz-grit anti-slip top surface suitable for the 50 mm pultruded I-bar grating for heavy plant platform?

How are these 50 mm pultruded I-bar grit panels for heavy plant platform fixed to the supports?

What panel size, MOQ and lead time apply to the 50 mm pultruded I-bar grit grating for heavy plant platform?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]