FRP/GRP Grating Specification · Heavy Traffic Platform
50 mm Pultruded I-bar FRP/GRP Grating, I-bar 50 mm Mesh, Concave Top for Heavy Traffic Platform
50 mm pultruded I-bar FRP/GRP grating configured with a concave top for heavy traffic platform. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.
Specification
| Product type | Pultruded I-bar FRP/GRP grating |
|---|---|
| Mesh | I-bar 50 mm |
| Depth | 50 mm |
| Standard panel | 1220 x 3660 mm, cut to size |
| Open area | confirm_with_factory |
| Unit weight | confirm_with_factory |
| Recommended resin | Isophthalic polyester |
| Surface | Concave (meniscus) top |
| Bar orientation | Unidirectional pultruded profile; bars run parallel to the main load path between bearers. |
Allowable uniform load by support span
| Support span | Allowable UDL (kN/m²) |
|---|---|
| 600 mm | 48 kN/m² |
| 900 mm | 26 kN/m² |
| 1200 mm | 14 kN/m² |
Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.
Selection rationale
On a platform crossed by maintenance vehicles, trolleys and rolling equipment, this 50 mm pultruded I-bar is sized against the repeated wheel loads, with section and bar direction checked against the actual wheel arrangement. A lighter molded profile would not suit this repeated rolling duty, and a specific wheel or point load outside the table requires separate review rather than a table estimate. The 50 mm I-bar member serves plant access decks around packaged equipment. The concave face channels water away from the walking line; no bonded grit layer is added. Bearing points and clip positions are laid out before fixing; exposed cut edges are dressed afterward. Layout and fixing follow the support drawing; the finish is matched to the service condition described above.
Section profile and fixing
The 50 mm pultruded I-bar is a heavy-duty section for wider support spacing, plant access decks and repeated rolling loads around packaged equipment. Unidirectional bars run parallel to the main load path; fix with rated clips to the support frame, check bar direction against the wheel or foot load, and finish cut openings by the factory.
Surface finish
The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.
Data availability
Weight per square metre and open mesh percentage for the 50 mm pultruded I-bar concave heavy traffic platform are not in the verified matrix and must be confirmed with the factory. Supplying them unlocks the self-weight check for bearer design and the passage-area calculation; the listed UDL values still guide the initial choice.
Resin selection
Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.
Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.
Installation, fixing and delivery
Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.
Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.
Request-for-quotation inputs
- Overall dimensions and required panel layout
- Support spacing / clear span and beam layout
- Design load: uniform, wheel or point load, and expected use
- Resin requirement and contact medium, concentration and temperature
- Surface finish (concave, grit or smooth)
- Quantity in square metres
- Destination country and any local standard to follow
Typical uses
- heavy traffic platform
- pultruded i-bar heavy traffic platform
- concave-top heavy traffic platform
- industrial personnel walkway
- corrosion-resistant platform deck
- open-mesh drainage and ventilation deck
