📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Rail And Metro Maintenance Walkway

50 mm Pultruded I-bar FRP/GRP Grating, I-bar 50 mm Mesh, Concave Top for Rail And Metro Maintenance Walkway

50 mm pultruded I-bar FRP/GRP grating configured with a concave top for rail and metro maintenance walkway. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typePultruded I-bar FRP/GRP grating
MeshI-bar 50 mm
Depth50 mm
Standard panel1220 x 3660 mm, cut to size
Open areaconfirm_with_factory
Unit weightconfirm_with_factory
Recommended resinIsophthalic polyester
SurfaceConcave (meniscus) top
Bar orientationUnidirectional pultruded profile; bars run parallel to the main load path between bearers.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm48 kN/m²
900 mm26 kN/m²
1200 mm14 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

Service walkways alongside rail tracks, metro guideways and signalling equipment zones. Maintenance access in a dry or sheltered corridor; non-conductive deck for personnel near electrical and signalling systems. Maintenance access beside tracks and guideways governs the corridor; the non-conductive deck serves personnel near electrical and signalling systems in a dry or sheltered route

The 50 mm I-bar member serves plant access decks around packaged equipment. Under L/200 deflection the table lists 48 kN/m² over 600 mm, 26 over 900 mm and 14 over 1200 mm for this member. Heavy rolling, point loads and cantilevers outside the verified table require separate engineering review.

A meniscus-shaped top that sheds runoff and keeps wet-foot grip on drained outdoor routes. Bearing points and clip positions are laid out before fixing; exposed cut edges are dressed afterward.

Cutouts and edges are finished after layout confirmation; the walking condition governs the finish choice.

Section profile and fixing

The 50 mm pultruded I-bar is a heavy-duty section for wider support spacing, plant access decks and repeated rolling loads around packaged equipment. Unidirectional bars run parallel to the main load path; fix with rated clips to the support frame, check bar direction against the wheel or foot load, and finish cut openings by the factory.

Surface finish

The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.

Data availability

For this 50 mm pultruded I-bar concave rail and metro maintenance walkway, unit weight and open area are confirm_with_factory pending the factory return. Once the figures arrive they set the deck self-weight used in support design and the ventilation or drainage passage; until then the verified UDL table remains the selection basis.

Resin selection

Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • rail and metro maintenance walkway
  • pultruded i-bar rail and metro maintenance walkway
  • concave-top rail and metro maintenance walkway
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 50 mm pultruded I-bar concave grating for rail and metro maintenance walkway carry at a 900 mm span?

Which resin suits the rail and metro maintenance walkway on this 50 mm pultruded I-bar concave grating?

Is the concave (meniscus) top surface suitable for the 50 mm pultruded I-bar grating for rail and metro maintenance walkway?

How are these 50 mm pultruded I-bar concave panels for rail and metro maintenance walkway fixed to the supports?

What panel size, MOQ and lead time apply to the 50 mm pultruded I-bar concave grating for rail and metro maintenance walkway?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]