📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Oil And Gas Facility Deck

50 mm Pultruded I-bar FRP/GRP Grating, I-bar 50 mm Mesh, Concave Top for Oil And Gas Facility Deck

50 mm pultruded I-bar FRP/GRP grating configured with a concave top for oil and gas facility deck. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typePultruded I-bar FRP/GRP grating
MeshI-bar 50 mm
Depth50 mm
Standard panel1220 x 3660 mm, cut to size
Open areaconfirm_with_factory
Unit weightconfirm_with_factory
Recommended resinIsophthalic polyester; vinyl ester where stronger attack is confirmed in writing
SurfaceConcave (meniscus) top
Bar orientationUnidirectional pultruded profile; bars run parallel to the main load path between bearers.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm48 kN/m²
900 mm26 kN/m²
1200 mm14 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

On process walkways and equipment platforms in upstream, midstream or refining-related facilities, this 50 mm pultruded I-bar handles a hydrocarbon atmosphere, local chemical traces and outdoor weather, with special area requirements confirmed separately. It is oversized for short light walks where molded would suffice, and any load outside the verified table or special zoning demand written engineering review. A 50 mm heavy-duty pultruded I-bar for wider supports and repeated rolling loads. The concave meniscus crown drains water off the contact patch and grips damp footwear without added grit. Panel direction, clips and edge bearing are checked to the frame drawing before fixing. Layout and fixing follow the support drawing; the finish is matched to the service condition described above.

Section profile and fixing

The 50 mm pultruded I-bar is a heavy-duty section for wider support spacing, plant access decks and repeated rolling loads around packaged equipment. Unidirectional bars run parallel to the main load path; fix with rated clips to the support frame, check bar direction against the wheel or foot load, and finish cut openings by the factory.

Surface finish

The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.

Data availability

Weight per square metre and open mesh percentage for the 50 mm pultruded I-bar concave oil and gas facility deck are not in the verified matrix and must be confirmed with the factory. Supplying them unlocks the self-weight check for bearer design and the passage-area calculation; the listed UDL values still guide the initial choice.

Resin selection

Isophthalic polyester; vinyl ester where stronger attack is confirmed in writing. Isophthalic polyester is the starting point; vinyl ester is substituted where the specific ore, brine or chemical stream warrants it, confirmed in writing.

Vinyl ester is substituted where the specific ore, brine or chemical stream warrants it, after written confirmation. Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • oil and gas facility deck
  • pultruded i-bar oil and gas facility deck
  • concave-top oil and gas facility deck
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 50 mm pultruded I-bar concave grating for oil and gas facility deck carry at a 900 mm span?

Which resin suits the oil and gas facility deck on this 50 mm pultruded I-bar concave grating?

Is the concave (meniscus) top surface suitable for the 50 mm pultruded I-bar grating for oil and gas facility deck?

How are these 50 mm pultruded I-bar concave panels for oil and gas facility deck fixed to the supports?

What panel size, MOQ and lead time apply to the 50 mm pultruded I-bar concave grating for oil and gas facility deck?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]