FRP/GRP Grating Specification · Offshore Marine Platform
50 mm Pultruded I-bar FRP/GRP Grating, I-bar 50 mm Mesh, Concave Top for Offshore Marine Platform
50 mm pultruded I-bar FRP/GRP grating configured with a concave top for offshore marine platform. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.
Specification
| Product type | Pultruded I-bar FRP/GRP grating |
|---|---|
| Mesh | I-bar 50 mm |
| Depth | 50 mm |
| Standard panel | 1220 x 3660 mm, cut to size |
| Open area | confirm_with_factory |
| Unit weight | confirm_with_factory |
| Recommended resin | Isophthalic polyester |
| Surface | Concave (meniscus) top |
| Bar orientation | Unidirectional pultruded profile; bars run parallel to the main load path between bearers. |
Allowable uniform load by support span
| Support span | Allowable UDL (kN/m²) |
|---|---|
| 600 mm | 48 kN/m² |
| 900 mm | 26 kN/m² |
| 1200 mm | 14 kN/m² |
Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.
Selection rationale
For offshore decks, marine modules, walkways and equipment supports, this 50 mm pultruded I-bar meets saltwater splash, marine atmosphere and weather, with special-area resin quoted on request. The section is reserved for wider or heavier service; light pedestrian routes would use a lighter profile, and splash, point or cantilever loads outside the table need separate review. The 50 mm I-bar member serves plant access decks around packaged equipment. A meniscus-shaped top that sheds runoff and keeps wet-foot grip on drained outdoor routes. Cut edges and openings are finished after the drawing and cutout positions are confirmed. Service access around the deck follows the approved layout; cut edges are dressed after confirmation.
Section profile and fixing
The 50 mm pultruded I-bar is a heavy-duty section for wider support spacing, plant access decks and repeated rolling loads around packaged equipment. Unidirectional bars run parallel to the main load path; fix with rated clips to the support frame, check bar direction against the wheel or foot load, and finish cut openings by the factory.
Surface finish
The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.
Data availability
The factory must confirm two fields for the 50 mm pultruded I-bar concave offshore marine platform: deck unit weight and open-area percentage. Those confirmed numbers feed the support self-weight design and the airflow or water passage sizing; the verified span loads are the interim reference while the reply is awaited.
Resin selection
Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.
Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.
Installation, fixing and delivery
Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.
Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.
Request-for-quotation inputs
- Overall dimensions and required panel layout
- Support spacing / clear span and beam layout
- Design load: uniform, wheel or point load, and expected use
- Resin requirement and contact medium, concentration and temperature
- Surface finish (concave, grit or smooth)
- Quantity in square metres
- Destination country and any local standard to follow
Typical uses
- offshore marine platform
- pultruded i-bar offshore marine platform
- concave-top offshore marine platform
- industrial personnel walkway
- corrosion-resistant platform deck
- open-mesh drainage and ventilation deck
