FRP/GRP Grating Specification · Heavy Plant Platform
50 mm Pultruded I-bar FRP/GRP Grating, I-bar 50 mm Mesh, Concave Top for Heavy Plant Platform
50 mm pultruded I-bar FRP/GRP grating configured with a concave top for heavy plant platform. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.
Specification
| Product type | Pultruded I-bar FRP/GRP grating |
|---|---|
| Mesh | I-bar 50 mm |
| Depth | 50 mm |
| Standard panel | 1220 x 3660 mm, cut to size |
| Open area | confirm_with_factory |
| Unit weight | confirm_with_factory |
| Recommended resin | Isophthalic polyester |
| Surface | Concave (meniscus) top |
| Bar orientation | Unidirectional pultruded profile; bars run parallel to the main load path between bearers. |
Allowable uniform load by support span
| Support span | Allowable UDL (kN/m²) |
|---|---|
| 600 mm | 48 kN/m² |
| 900 mm | 26 kN/m² |
| 1200 mm | 14 kN/m² |
Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.
Selection rationale
Around heavy process equipment, machinery bases and plant modules, this 50 mm pultruded I-bar forms a raised maintenance platform beside heavy units, meeting local ambient exposure with occasional spill cleanup. The section is not for light short-span walks where molded would do, and wheel, point or cantilever loads outside the table are reviewed separately. The 50 mm profile bridges longer bearer gaps than molded panels where rolling and wheeled access recur. A meniscus-shaped top that sheds runoff and keeps wet-foot grip on drained outdoor routes. Support bearing and clip spacing follow the approved layout; edges are checked for even contact. The panel is laid to the section direction; upkeep follows the care guidance for the chosen top.
Section profile and fixing
The 50 mm pultruded I-bar is a heavy-duty section for wider support spacing, plant access decks and repeated rolling loads around packaged equipment. Unidirectional bars run parallel to the main load path; fix with rated clips to the support frame, check bar direction against the wheel or foot load, and finish cut openings by the factory.
Surface finish
The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.
Data availability
For this 50 mm pultruded I-bar concave heavy plant platform, unit weight and open area are confirm_with_factory pending the factory return. Once the figures arrive they set the deck self-weight used in support design and the ventilation or drainage passage; until then the verified UDL table remains the selection basis.
Resin selection
Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.
Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.
Installation, fixing and delivery
Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.
Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.
Request-for-quotation inputs
- Overall dimensions and required panel layout
- Support spacing / clear span and beam layout
- Design load: uniform, wheel or point load, and expected use
- Resin requirement and contact medium, concentration and temperature
- Surface finish (concave, grit or smooth)
- Quantity in square metres
- Destination country and any local standard to follow
Typical uses
- heavy plant platform
- pultruded i-bar heavy plant platform
- concave-top heavy plant platform
- industrial personnel walkway
- corrosion-resistant platform deck
- open-mesh drainage and ventilation deck
