📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Equipment Support Deck

50 mm Pultruded I-bar FRP/GRP Grating, I-bar 50 mm Mesh, Concave Top for Equipment Support Deck

50 mm pultruded I-bar FRP/GRP grating configured with a concave top for equipment support deck. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typePultruded I-bar FRP/GRP grating
MeshI-bar 50 mm
Depth50 mm
Standard panel1220 x 3660 mm, cut to size
Open areaconfirm_with_factory
Unit weightconfirm_with_factory
Recommended resinIsophthalic polyester
SurfaceConcave (meniscus) top
Bar orientationUnidirectional pultruded profile; bars run parallel to the main load path between bearers.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm48 kN/m²
900 mm26 kN/m²
1200 mm14 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

Alongside packaged production equipment, skids and plant modules, the 50 mm pultruded I-bar carries a maintenance-access deck beside static equipment loads; the bearing layout follows the equipment support frame. This 50 mm profile suits wider bearer spacing around packaged units rather than the lightest footpaths. The meniscus crown drains runoff off the contact patch, with no bonded grit layer added. Fixing clips and edge bearing follow the frame drawing, and cut edges are dressed after layout confirmation. Around each skid, the bearing points are checked to the equipment supports before the grating is fixed down.

Section profile and fixing

The 50 mm pultruded I-bar is a heavy-duty section for wider support spacing, plant access decks and repeated rolling loads around packaged equipment. Unidirectional bars run parallel to the main load path; fix with rated clips to the support frame, check bar direction against the wheel or foot load, and finish cut openings by the factory.

Surface finish

The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.

Data availability

For this 50 mm pultruded I-bar concave equipment support deck, unit weight and open area are confirm_with_factory pending the factory return. Once the figures arrive they set the deck self-weight used in support design and the ventilation or drainage passage; until then the verified UDL table remains the selection basis.

Resin selection

Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • equipment support deck
  • pultruded i-bar equipment support deck
  • concave-top equipment support deck
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 50 mm pultruded I-bar concave grating for equipment support deck carry at a 900 mm span?

Which resin suits the equipment support deck on this 50 mm pultruded I-bar concave grating?

Is the concave (meniscus) top surface suitable for the 50 mm pultruded I-bar grating for equipment support deck?

How are these 50 mm pultruded I-bar concave panels for equipment support deck fixed to the supports?

What panel size, MOQ and lead time apply to the 50 mm pultruded I-bar concave grating for equipment support deck?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]