📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Chemical Plant Deck

50 mm Pultruded I-bar FRP/GRP Grating, I-bar 50 mm Mesh, Concave Top for Chemical Plant Deck

50 mm pultruded I-bar FRP/GRP grating configured with a concave top for chemical plant deck. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typePultruded I-bar FRP/GRP grating
MeshI-bar 50 mm
Depth50 mm
Standard panel1220 x 3660 mm, cut to size
Open areaconfirm_with_factory
Unit weightconfirm_with_factory
Recommended resinVinyl ester
SurfaceConcave (meniscus) top
Bar orientationUnidirectional pultruded profile; bars run parallel to the main load path between bearers.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm48 kN/m²
900 mm26 kN/m²
1200 mm14 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

On heavier process decks around reactors and dosing lines, this 50 mm pultruded I-bar is the heavy-duty choice for wider support spacing and repeated rolling loads around packaged equipment, with resin matched to the chemical brief. It should not be specified for light short-span walkways where a molded section would suffice, and loads beyond the verified table — wheel, point or cantilever — need separate engineering review. The 50 mm I-bar member serves plant access decks around packaged equipment. A meniscus-shaped top that sheds runoff and keeps wet-foot grip on drained outdoor routes. Bearing points and clip positions are laid out before fixing; exposed cut edges are dressed afterward. The panel is laid to the section direction; upkeep follows the care guidance for the chosen top.

Section profile and fixing

The 50 mm pultruded I-bar is a heavy-duty section for wider support spacing, plant access decks and repeated rolling loads around packaged equipment. Unidirectional bars run parallel to the main load path; fix with rated clips to the support frame, check bar direction against the wheel or foot load, and finish cut openings by the factory.

Surface finish

The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.

Data availability

The factory must confirm two fields for the 50 mm pultruded I-bar concave chemical plant deck: deck unit weight and open-area percentage. Those confirmed numbers feed the support self-weight design and the airflow or water passage sizing; the verified span loads are the interim reference while the reply is awaited.

Resin selection

Vinyl ester. Vinyl ester is selected for strong acid, bleach, caustic and scrubber service; concentration and temperature must be confirmed in writing.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • chemical plant deck
  • pultruded i-bar chemical plant deck
  • concave-top chemical plant deck
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 50 mm pultruded I-bar concave grating for chemical plant deck carry at a 900 mm span?

Which resin suits the chemical plant deck on this 50 mm pultruded I-bar concave grating?

Is the concave (meniscus) top surface suitable for the 50 mm pultruded I-bar grating for chemical plant deck?

How are these 50 mm pultruded I-bar concave panels for chemical plant deck fixed to the supports?

What panel size, MOQ and lead time apply to the 50 mm pultruded I-bar concave grating for chemical plant deck?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]