FRP/GRP Grating Specification · Overslung Bridge Walkway
50 mm Pultruded I-bar FRP/GRP Grating, I-bar 50 mm Mesh, Concave Top for Overslung Bridge Walkway
50 mm pultruded I-bar FRP/GRP grating configured with a concave top for overslung bridge walkway. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.
Specification
| Product type | Pultruded I-bar FRP/GRP grating |
|---|---|
| Mesh | I-bar 50 mm |
| Depth | 50 mm |
| Standard panel | 1220 x 3660 mm, cut to size |
| Open area | confirm_with_factory |
| Unit weight | confirm_with_factory |
| Recommended resin | Isophthalic polyester |
| Surface | Concave (meniscus) top |
| Bar orientation | Unidirectional pultruded profile; bars run parallel to the main load path between bearers. |
Allowable uniform load by support span
| Support span | Allowable UDL (kN/m²) |
|---|---|
| 600 mm | 48 kN/m² |
| 900 mm | 26 kN/m² |
| 1200 mm | 14 kN/m² |
Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.
Selection rationale
elevated walkway bridge connecting buildings, units or process areas across a gap; longer unsupported span between bridge frames; personnel and occasional light trolley crossing over the bridge
The 50 mm I-bar member serves plant access decks around packaged equipment. Under L/200 deflection the table lists 48 kN/m² over 600 mm, 26 over 900 mm and 14 over 1200 mm for this member. Long spans, wheel loads and concentrated footings are checked against the span table and project review.
The crowned concave profile keeps runoff off the stepping surface while remaining grit-free. Support bearing and clip spacing follow the approved layout; edges are checked for even contact.
Layout and fixing follow the support drawing; the finish is matched to the service condition described above.
Section profile and fixing
The 50 mm pultruded I-bar is a heavy-duty section for wider support spacing, plant access decks and repeated rolling loads around packaged equipment. Unidirectional bars run parallel to the main load path; fix with rated clips to the support frame, check bar direction against the wheel or foot load, and finish cut openings by the factory.
Surface finish
The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.
Data availability
Weight per square metre and open mesh percentage for the 50 mm pultruded I-bar concave overslung bridge walkway are not in the verified matrix and must be confirmed with the factory. Supplying them unlocks the self-weight check for bearer design and the passage-area calculation; the listed UDL values still guide the initial choice.
Resin selection
Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.
Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.
Installation, fixing and delivery
Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.
Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.
Request-for-quotation inputs
- Overall dimensions and required panel layout
- Support spacing / clear span and beam layout
- Design load: uniform, wheel or point load, and expected use
- Resin requirement and contact medium, concentration and temperature
- Surface finish (concave, grit or smooth)
- Quantity in square metres
- Destination country and any local standard to follow
Typical uses
- overslung bridge walkway
- pultruded i-bar overslung bridge walkway
- concave-top overslung bridge walkway
- industrial personnel walkway
- corrosion-resistant platform deck
- open-mesh drainage and ventilation deck
