FRP/GRP Grating Specification · Oil And Hydraulic Walkway
38 mm Pultruded I-bar FRP/GRP Grating, I-bar 38 mm Mesh, Concave Top for Oil And Hydraulic Walkway
38 mm pultruded I-bar FRP/GRP grating configured with a concave top for oil and hydraulic walkway. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.
Specification
| Product type | Pultruded I-bar FRP/GRP grating |
|---|---|
| Mesh | I-bar 38 mm |
| Depth | 38 mm |
| Standard panel | 1220 x 3660 mm, cut to size |
| Open area | confirm_with_factory |
| Unit weight | confirm_with_factory |
| Recommended resin | Isophthalic polyester |
| Surface | Concave (meniscus) top |
| Bar orientation | Unidirectional pultruded profile; the deck must be laid so bars span between supports in the load direction. |
Allowable uniform load by support span
| Support span | Allowable UDL (kN/m²) |
|---|---|
| 600 mm | 35 kN/m² |
| 900 mm | 18 kN/m² |
| 1200 mm | 9 kN/m² |
Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.
Selection rationale
Around hydraulic power units, lube stations and mineral-oil handling areas, this 38 mm pultruded I-bar walkway sits over a mostly dry deck that sees mineral and hydraulic oil spillage with occasional cleaning and drainage. The unidirectional profile must align with the load path between bearers; it is not the HD class for long heavy decks, and oils outside the resin resistance table are checked in writing. A 38 mm pultruded I-bar with higher stiffness along the bar direction than an equivalent molded panel. The concave face channels water away from the walking line; no bonded grit layer is added. The frame drawing sets the fixing points; cutout edges are finished once positions are confirmed. Layout and fixing follow the support drawing; the finish is matched to the service condition described above.
Section profile and fixing
The 38 mm pultruded I-bar gives higher stiffness along the bar direction than an equivalent molded panel, suiting industrial decks and corrosive plant walkways on defined spans. Bars must span between supports in the load direction; align the I-bar line with the main load path, space clips to the bearer layout, and verify edge bearing before fixing.
Surface finish
The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.
Data availability
For this 38 mm pultruded I-bar concave oil and hydraulic walkway, unit weight and open area are confirm_with_factory pending the factory return. Once the figures arrive they set the deck self-weight used in support design and the ventilation or drainage passage; until then the verified UDL table remains the selection basis.
Resin selection
Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.
Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.
Installation, fixing and delivery
Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.
Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.
Request-for-quotation inputs
- Overall dimensions and required panel layout
- Support spacing / clear span and beam layout
- Design load: uniform, wheel or point load, and expected use
- Resin requirement and contact medium, concentration and temperature
- Surface finish (concave, grit or smooth)
- Quantity in square metres
- Destination country and any local standard to follow
Typical uses
- oil and hydraulic walkway
- pultruded i-bar oil and hydraulic walkway
- concave-top oil and hydraulic walkway
- industrial personnel walkway
- corrosion-resistant platform deck
- open-mesh drainage and ventilation deck
