📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Chemical Plant Deck

38 mm Pultruded I-bar FRP/GRP Grating, I-bar 38 mm Mesh, Concave Top for Chemical Plant Deck

38 mm pultruded I-bar FRP/GRP grating configured with a concave top for chemical plant deck. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typePultruded I-bar FRP/GRP grating
MeshI-bar 38 mm
Depth38 mm
Standard panel1220 x 3660 mm, cut to size
Open areaconfirm_with_factory
Unit weightconfirm_with_factory
Recommended resinVinyl ester
SurfaceConcave (meniscus) top
Bar orientationUnidirectional pultruded profile; the deck must be laid so bars span between supports in the load direction.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm35 kN/m²
900 mm18 kN/m²
1200 mm9 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

On platforms and walkways around reactors, dosing stations and pipe racks, this 38 mm pultruded I-bar meets possible acid, alkali or solvent vapour and spillage, with resin matched to the specific chemical brief. Bars must span between supports in the load direction; this section is not meant across the load path and is not the HD duty for the heaviest decks, and aggressive media are confirmed in writing before order. A 38 mm pultruded I-bar with higher stiffness along the bar direction than an equivalent molded panel. The concave meniscus crown drains water off the contact patch and grips damp footwear without added grit. The frame drawing sets the fixing points; cutout edges are finished once positions are confirmed. Cutouts and edges are finished after layout confirmation; the walking condition governs the finish choice.

Section profile and fixing

The 38 mm pultruded I-bar gives higher stiffness along the bar direction than an equivalent molded panel, suiting industrial decks and corrosive plant walkways on defined spans. Bars must span between supports in the load direction; align the I-bar line with the main load path, space clips to the bearer layout, and verify edge bearing before fixing.

Surface finish

The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.

Data availability

The factory must confirm two fields for the 38 mm pultruded I-bar concave chemical plant deck: deck unit weight and open-area percentage. Those confirmed numbers feed the support self-weight design and the airflow or water passage sizing; the verified span loads are the interim reference while the reply is awaited.

Resin selection

Vinyl ester. Vinyl ester is selected for strong acid, bleach, caustic and scrubber service; concentration and temperature must be confirmed in writing.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • chemical plant deck
  • pultruded i-bar chemical plant deck
  • concave-top chemical plant deck
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 38 mm pultruded I-bar concave grating for chemical plant deck carry at a 900 mm span?

Which resin suits the chemical plant deck on this 38 mm pultruded I-bar concave grating?

Is the concave (meniscus) top surface suitable for the 38 mm pultruded I-bar grating for chemical plant deck?

How are these 38 mm pultruded I-bar concave panels for chemical plant deck fixed to the supports?

What panel size, MOQ and lead time apply to the 38 mm pultruded I-bar concave grating for chemical plant deck?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]