📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Spill Containment Deck

38 mm Molded FRP/GRP Grating, 50 x 50 mm Mesh, Smooth Top for Spill Containment Deck

38 mm molded FRP/GRP grating, 50 x 50 mm open mesh configured with a smooth top for spill containment deck. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typeMolded FRP/GRP grating
Mesh50 x 50 mm
Depth38 mm
Standard panel1220 x 3660 mm, cut to size
Open areaconfirm_with_factory
Unit weightconfirm_with_factory
Recommended resinIsophthalic polyester; vinyl ester where stronger attack is confirmed in writing
SurfaceSmooth top
Bar orientationBidirectional molded lay-up with a wider opening, intended for drainage, ventilation and spill decks rather than fine-foot retention.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm22 kN/m²
900 mm10 kN/m²
1200 mm5.5 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

open spill deck and bund grating around process vessels where liquids must drain freely; occasional chemical or liquid spillage over an open mesh; resin matched to the spilled medium in the brief

This 38 mm 50 x 50 molded section targets drainage, ventilation and spill decks. Against the planned supports, the verified ratings read 22 kN/m² at 600 mm, 10 at 900 mm and 5.5 at 1200 mm, L/200. Long spans, wheel loads and concentrated footings are checked against the span table and project review.

The plain flat finish releases dirt and rinse water quickly for hygienic or dry service zones. Panel direction, clips and edge bearing are checked to the frame drawing before fixing.

The panel is laid to the section direction; upkeep follows the care guidance for the chosen top.

Section profile and fixing

The 38 mm 50 x 50 mesh opens the deck to pass water, vapour and small debris, while still carrying the molded-section load class on fewer bearing bars. Bidirectional molded lay-up; lay the panel to the channel or equipment line, secure with non-corrosive clips, and confirm cutout edges against the drawing.

Surface finish

The smooth face sheds dust and wash-down water cleanly and is easy to sweep, hose or wipe in dry and hygienic areas. Wash-down rooms, dry storage decks, landscaped promenades and areas where debris must not lodge in the surface.

Data availability

Weight per square metre and open mesh percentage for the 38 mm molded 50 x 50 smooth spill containment deck are not in the verified matrix and must be confirmed with the factory. Supplying them unlocks the self-weight check for bearer design and the passage-area calculation; the listed UDL values still guide the initial choice.

Resin selection

Isophthalic polyester; vinyl ester where stronger attack is confirmed in writing. Isophthalic polyester is the starting point; vinyl ester is substituted where the specific ore, brine or chemical stream warrants it, confirmed in writing.

Vinyl ester is substituted where the specific ore, brine or chemical stream warrants it, after written confirmation. Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • spill containment deck
  • molded spill containment deck
  • smooth-top spill containment deck
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 38 mm molded 50 x 50 smooth grating for spill containment deck carry at a 900 mm span?

Which resin suits the spill containment deck on this 38 mm molded 50 x 50 smooth grating?

Is the smooth top surface suitable for the 38 mm molded 50 x 50 grating for spill containment deck?

How are these 38 mm molded 50 x 50 smooth panels for spill containment deck fixed to the supports?

What panel size, MOQ and lead time apply to the 38 mm molded 50 x 50 smooth grating for spill containment deck?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]