FRP/GRP Grating Specification · Wastewater Treatment Deck
38 mm Molded FRP/GRP Grating, 50 x 50 mm Mesh, Concave Top for Wastewater Treatment Deck
38 mm molded FRP/GRP grating, 50 x 50 mm open mesh configured with a concave top for wastewater treatment deck. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.
Specification
| Product type | Molded FRP/GRP grating |
|---|---|
| Mesh | 50 x 50 mm |
| Depth | 38 mm |
| Standard panel | 1220 x 3660 mm, cut to size |
| Open area | confirm_with_factory |
| Unit weight | confirm_with_factory |
| Recommended resin | Isophthalic polyester |
| Surface | Concave (meniscus) top |
| Bar orientation | Bidirectional molded lay-up with a wider opening, intended for drainage, ventilation and spill decks rather than fine-foot retention. |
Allowable uniform load by support span
| Support span | Allowable UDL (kN/m²) |
|---|---|
| 600 mm | 22 kN/m² |
| 900 mm | 10 kN/m² |
| 1200 mm | 5.5 kN/m² |
Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.
Selection rationale
Around clarifiers, screens and channels in a wastewater works, this 38 mm molded 50 x 50 grating handles humid air, intermittent effluent and damp underfoot while keeping the deck open and drained. The 50 x 50 mesh passes small debris, so it is not for locations where tools must be retained, and heavy concentrated loads exceed this molded class. A 38 mm molded 50 x 50 open-mesh panel that passes water, vapour and small debris freely. The concave meniscus crown drains water off the contact patch and grips damp footwear without added grit. Panel direction, clips and edge bearing are checked to the frame drawing before fixing. The panel is laid to the section direction; upkeep follows the care guidance for the chosen top.
Section profile and fixing
The 38 mm 50 x 50 mesh opens the deck to pass water, vapour and small debris, while still carrying the molded-section load class on fewer bearing bars. Bidirectional molded lay-up; lay the panel to the channel or equipment line, secure with non-corrosive clips, and confirm cutout edges against the drawing.
Surface finish
The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.
Data availability
The factory must confirm two fields for the 38 mm molded 50 x 50 concave wastewater treatment deck: deck unit weight and open-area percentage. Those confirmed numbers feed the support self-weight design and the airflow or water passage sizing; the verified span loads are the interim reference while the reply is awaited.
Resin selection
Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.
Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.
Installation, fixing and delivery
Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.
Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.
Request-for-quotation inputs
- Overall dimensions and required panel layout
- Support spacing / clear span and beam layout
- Design load: uniform, wheel or point load, and expected use
- Resin requirement and contact medium, concentration and temperature
- Surface finish (concave, grit or smooth)
- Quantity in square metres
- Destination country and any local standard to follow
Typical uses
- wastewater treatment deck
- molded wastewater treatment deck
- concave-top wastewater treatment deck
- industrial personnel walkway
- corrosion-resistant platform deck
- open-mesh drainage and ventilation deck
