📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Coastal Jetty Walkway

38 mm Molded FRP/GRP Grating, 50 x 50 mm Mesh, Concave Top for Coastal Jetty Walkway

38 mm molded FRP/GRP grating, 50 x 50 mm open mesh configured with a concave top for coastal jetty walkway. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typeMolded FRP/GRP grating
Mesh50 x 50 mm
Depth38 mm
Standard panel1220 x 3660 mm, cut to size
Open areaconfirm_with_factory
Unit weightconfirm_with_factory
Recommended resinIsophthalic polyester
SurfaceConcave (meniscus) top
Bar orientationBidirectional molded lay-up with a wider opening, intended for drainage, ventilation and spill decks rather than fine-foot retention.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm22 kN/m²
900 mm10 kN/m²
1200 mm5.5 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

On jetty walks and harbour service decks exposed to salt-laden air and splash, this 38 mm molded 50 x 50 panel uses its wider opening to pass spray and drainage while bearing service personnel and light maintenance access. The wider mesh trades fine-foot retention and concentrated-bar width; it is not for heavy equipment footings or duties where small items must not fall through, and long heavy marine decks need a deeper profile. A 38 mm molded 50 x 50 open-mesh panel that passes water, vapour and small debris freely. The concave meniscus crown drains water off the contact patch and grips damp footwear without added grit. On site the panel follows the section direction; fixing clips and bearing are verified against the layout. The panel is laid to the section direction; upkeep follows the care guidance for the chosen top.

Section profile and fixing

The 38 mm 50 x 50 mesh opens the deck to pass water, vapour and small debris, while still carrying the molded-section load class on fewer bearing bars. Bidirectional molded lay-up; lay the panel to the channel or equipment line, secure with non-corrosive clips, and confirm cutout edges against the drawing.

Surface finish

The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.

Data availability

For this 38 mm molded 50 x 50 concave coastal jetty walkway, unit weight and open area are confirm_with_factory pending the factory return. Once the figures arrive they set the deck self-weight used in support design and the ventilation or drainage passage; until then the verified UDL table remains the selection basis.

Resin selection

Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • coastal jetty walkway
  • molded coastal jetty walkway
  • concave-top coastal jetty walkway
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 38 mm molded 50 x 50 concave grating for coastal jetty walkway carry at a 900 mm span?

Which resin suits the coastal jetty walkway on this 38 mm molded 50 x 50 concave grating?

Is the concave (meniscus) top surface suitable for the 38 mm molded 50 x 50 grating for coastal jetty walkway?

How are these 38 mm molded 50 x 50 concave panels for coastal jetty walkway fixed to the supports?

What panel size, MOQ and lead time apply to the 38 mm molded 50 x 50 concave grating for coastal jetty walkway?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]