📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Car Wash Floor

38 mm Molded FRP/GRP Grating, 38 x 38 mm Mesh, Smooth Top for Car Wash Floor

38 mm molded FRP/GRP grating, 38 x 38 mm mesh configured with a smooth top for car wash floor. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typeMolded FRP/GRP grating
Mesh38 x 38 mm
Depth38 mm
Standard panel1220 x 3660 mm, cut to size
Open area68 %
Unit weight19.5 kg/m²
Recommended resinIsophthalic polyester
SurfaceSmooth top
Bar orientationBidirectional molded lay-up shares the load between crossing bars, suiting repeated foot traffic and light rolling loads.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm25 kN/m²
900 mm12 kN/m²
1200 mm6.5 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

This 38 mm molded 38 x 38 smooth panel serves wet car-wash bays and drainage floors exposed to continuous rinse water, detergents, occasional grease and standing drained water between cycles. A smooth face is not meant for wet or oily slopes and stair nosings needing anti-slip grip, nor for long spans under rolling equipment. This 38 mm molded section balances open mesh and stiffness for industrial walkways and platforms. The smooth panel wipes or hoses down without lodging debris in an open grit texture. The frame drawing sets the fixing points; cutout edges are finished once positions are confirmed. Cutouts and edges are finished after layout confirmation; the walking condition governs the finish choice.

Section profile and fixing

The 38 mm molded panel balances stiffness, open area and self-weight for general platforms and medium-span decks carrying steady foot traffic and light rolling loads. The bidirectional molded bars share the load across both directions; fix with M/C/L/Z clips, keep edge bearing even, and trim cut edges after layout confirmation.

Surface finish

The smooth face sheds dust and wash-down water cleanly and is easy to sweep, hose or wipe in dry and hygienic areas. Wash-down rooms, dry storage decks, landscaped promenades and areas where debris must not lodge in the surface.

Data availability

For this 38 mm molded 38 x 38 smooth car wash floor, unit weight 19.5 kg/m² and open area 68 % are verified, so these two fields do not require factory confirmation.

Resin selection

Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • car wash floor
  • molded car wash floor
  • smooth-top car wash floor
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 38 mm molded 38 x 38 smooth grating for car wash floor carry at a 900 mm span?

Which resin suits the car wash floor on this 38 mm molded 38 x 38 smooth grating?

Is the smooth top surface suitable for the 38 mm molded 38 x 38 grating for car wash floor?

How are these 38 mm molded 38 x 38 smooth panels for car wash floor fixed to the supports?

What panel size, MOQ and lead time apply to the 38 mm molded 38 x 38 smooth grating for car wash floor?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]