📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Stair Tread

38 mm Molded FRP/GRP Grating, 38 x 38 mm Mesh, Grit Top for Stair Tread

38 mm molded FRP/GRP grating, 38 x 38 mm mesh configured with a grit top for stair tread. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typeMolded FRP/GRP grating
Mesh38 x 38 mm
Depth38 mm
Standard panel1220 x 3660 mm, cut to size
Open area68 %
Unit weight19.5 kg/m²
Recommended resinIsophthalic polyester
SurfaceQuartz-grit anti-slip top
Bar orientationBidirectional molded lay-up shares the load between crossing bars, suiting repeated foot traffic and light rolling loads.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm25 kN/m²
900 mm12 kN/m²
1200 mm6.5 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

stair treads and landing nosings for external or internal industrial staircases; repeated foot impact on steps, often wet or dusty, with anti-slip performance required at the nosing

This 38 mm molded section balances open mesh and stiffness for industrial walkways and platforms. Against the planned supports, the verified ratings read 25 kN/m² at 600 mm, 12 at 900 mm and 6.5 at 1200 mm, L/200. Heavy rolling, point loads and cantilevers outside the verified table require separate engineering review.

A bonded quartz-grit layer raises slip resistance on ramps, stairs and busy oily treads. Panel direction, clips and edge bearing are checked to the frame drawing before fixing.

The panel is laid to the section direction; upkeep follows the care guidance for the chosen top.

Section profile and fixing

The 38 mm molded panel balances stiffness, open area and self-weight for general platforms and medium-span decks carrying steady foot traffic and light rolling loads. The bidirectional molded bars share the load across both directions; fix with M/C/L/Z clips, keep edge bearing even, and trim cut edges after layout confirmation.

Surface finish

A bonded quartz-grit layer raises slip resistance on ramps, stairs, busy outdoor steps and oily or intermittently wet treads. Ramps, stair treads, heavy-traffic platforms and exposed routes where extra anti-slip margin is required.

Data availability

The verified matrix lists 19.5 kg/m² unit weight and 68 % open area for the 38 mm molded 38 x 38 grit stair tread; no factory follow-up is needed on weight or open area.

Resin selection

Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • stair tread
  • molded stair tread
  • grit-top stair tread
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 38 mm molded 38 x 38 grit grating for stair tread carry at a 900 mm span?

Which resin suits the stair tread on this 38 mm molded 38 x 38 grit grating?

Is the quartz-grit anti-slip top surface suitable for the 38 mm molded 38 x 38 grating for stair tread?

How are these 38 mm molded 38 x 38 grit panels for stair tread fixed to the supports?

What panel size, MOQ and lead time apply to the 38 mm molded 38 x 38 grit grating for stair tread?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]