📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Car Wash Floor

25 mm Molded FRP/GRP Grating, 38 x 38 mm Mesh, Smooth Top for Car Wash Floor

25 mm molded FRP/GRP grating, 38 x 38 mm mesh configured with a smooth top for car wash floor. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typeMolded FRP/GRP grating
Mesh38 x 38 mm
Depth25 mm
Standard panel1220 x 3660 mm, cut to size
Open area68 %
Unit weight12.5 kg/m²
Recommended resinIsophthalic polyester
SurfaceSmooth top
Bar orientationBidirectional molded lay-up distributes foot and light equipment loads across both bar directions.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm12.5 kN/m²
900 mm6.0 kN/m²
1200 mm3.2 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

A wet bay and drainage floor for an automatic or hand car wash is served by this 25 mm molded 38 x 38 smooth panel, which meets continuous rinse water, detergents and occasional grease with standing drained water between cycles. The smooth face is not a choice for wet or oily inclines and stair nosings that need an anti-slip finish, nor for long spans carrying rolling equipment. This 25 mm molded section is the economical lightweight option when deck depth must stay low. A plain easy-clean top for wash-down rooms, dry storage decks and debris-sensitive zones. On site the panel follows the section direction; fixing clips and bearing are verified against the layout. Cutouts and edges are finished after layout confirmation; the walking condition governs the finish choice.

Section profile and fixing

The 25 mm molded panel suits short, lightly trafficked decks where a low-profile, lightweight bearing is enough for personnel and occasional light equipment. As a bidirectional molded lay-up, the panel can be oriented either way on the supports; clips are spaced to the frame layout, and edges are checked for even bearing.

Surface finish

The smooth face sheds dust and wash-down water cleanly and is easy to sweep, hose or wipe in dry and hygienic areas. Wash-down rooms, dry storage decks, landscaped promenades and areas where debris must not lodge in the surface.

Data availability

For this 25 mm molded 38 x 38 smooth car wash floor, unit weight 12.5 kg/m² and open area 68 % are verified, so these two fields do not require factory confirmation.

Resin selection

Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • car wash floor
  • molded car wash floor
  • smooth-top car wash floor
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 25 mm molded 38 x 38 smooth grating for car wash floor carry at a 900 mm span?

Which resin suits the car wash floor on this 25 mm molded 38 x 38 smooth grating?

Is the smooth top surface suitable for the 25 mm molded 38 x 38 grating for car wash floor?

How are these 25 mm molded 38 x 38 smooth panels for car wash floor fixed to the supports?

What panel size, MOQ and lead time apply to the 25 mm molded 38 x 38 smooth grating for car wash floor?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]