📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Stair Tread

25 mm Molded FRP/GRP Grating, 38 x 38 mm Mesh, Grit Top for Stair Tread

25 mm molded FRP/GRP grating, 38 x 38 mm mesh configured with a grit top for stair tread. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typeMolded FRP/GRP grating
Mesh38 x 38 mm
Depth25 mm
Standard panel1220 x 3660 mm, cut to size
Open area68 %
Unit weight12.5 kg/m²
Recommended resinIsophthalic polyester
SurfaceQuartz-grit anti-slip top
Bar orientationBidirectional molded lay-up distributes foot and light equipment loads across both bar directions.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm12.5 kN/m²
900 mm6.0 kN/m²
1200 mm3.2 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

Stair treads and landing nosings for external or internal industrial staircases. Repeated foot impact on steps, often wet or dusty, with anti-slip performance required at the nosing. Repeated step impact and nosing wear govern the tread; the surface must grip wet or dusty footwear and hold up to daily stair traffic in an internal or external staircase

A light 25 mm molded panel for short, lightly trafficked decks where a low-profile bearing suffices. Span-load figures below run 12.5 kN/m² (600 mm), 6.0 (900 mm) and 3.2 (1200 mm) on an L/200 simple span. Heavy rolling, point loads and cantilevers outside the verified table require separate engineering review.

The grit top provides extra anti-slip margin on inclined and high-traffic exposed routes. Cut edges and openings are finished after the drawing and cutout positions are confirmed.

Service access around the deck follows the approved layout; cut edges are dressed after confirmation.

Section profile and fixing

The 25 mm molded panel suits short, lightly trafficked decks where a low-profile, lightweight bearing is enough for personnel and occasional light equipment. As a bidirectional molded lay-up, the panel can be oriented either way on the supports; clips are spaced to the frame layout, and edges are checked for even bearing.

Surface finish

A bonded quartz-grit layer raises slip resistance on ramps, stairs, busy outdoor steps and oily or intermittently wet treads. Ramps, stair treads, heavy-traffic platforms and exposed routes where extra anti-slip margin is required.

Data availability

For this 25 mm molded 38 x 38 grit stair tread, unit weight 12.5 kg/m² and open area 68 % are verified, so these two fields do not require factory confirmation.

Resin selection

Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • stair tread
  • molded stair tread
  • grit-top stair tread
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 25 mm molded 38 x 38 grit grating for stair tread carry at a 900 mm span?

Which resin suits the stair tread on this 25 mm molded 38 x 38 grit grating?

Is the quartz-grit anti-slip top surface suitable for the 25 mm molded 38 x 38 grating for stair tread?

How are these 25 mm molded 38 x 38 grit panels for stair tread fixed to the supports?

What panel size, MOQ and lead time apply to the 25 mm molded 38 x 38 grit grating for stair tread?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]