📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · General Walkway

25 mm Molded FRP/GRP Grating, 38 x 38 mm Mesh, Concave Top for General Walkway

25 mm molded FRP/GRP grating, 38 x 38 mm mesh configured with a concave top for general walkway. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typeMolded FRP/GRP grating
Mesh38 x 38 mm
Depth25 mm
Standard panel1220 x 3660 mm, cut to size
Open area68 %
Unit weight12.5 kg/m²
Recommended resinIsophthalic polyester
SurfaceConcave (meniscus) top
Bar orientationBidirectional molded lay-up distributes foot and light equipment loads across both bar directions.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm12.5 kN/m²
900 mm6.0 kN/m²
1200 mm3.2 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

A general-purpose industrial walkway for personnel moving between equipment, process units and building exits. Routine foot traffic under outdoor or moist atmospheric conditions, without sustained chemical spillage. Routine personnel movement between units and exits is the governing duty; the deck must stay comfortable under standard safety footwear and resist the local ambient atmosphere without trapping water

The low-profile 25 mm molded member suits personnel and occasional light equipment on short bearer spans. Span-load figures below run 12.5 kN/m² (600 mm), 6.0 (900 mm) and 3.2 (1200 mm) on an L/200 simple span. Bearing spacing and any wheel, point or cantilever load are confirmed against the verified table before fixing.

The concave meniscus crown drains water off the contact patch and grips damp footwear without added grit. Support bearing and clip spacing follow the approved layout; edges are checked for even contact.

Layout and fixing follow the support drawing; the finish is matched to the service condition described above.

Section profile and fixing

The 25 mm molded panel suits short, lightly trafficked decks where a low-profile, lightweight bearing is enough for personnel and occasional light equipment. As a bidirectional molded lay-up, the panel can be oriented either way on the supports; clips are spaced to the frame layout, and edges are checked for even bearing.

Surface finish

The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.

Data availability

The verified matrix lists 12.5 kg/m² unit weight and 68 % open area for the 25 mm molded 38 x 38 concave general walkway; no factory follow-up is needed on weight or open area.

Resin selection

Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • general walkway
  • molded general walkway
  • concave-top general walkway
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 25 mm molded 38 x 38 concave grating for general walkway carry at a 900 mm span?

Which resin suits the general walkway on this 25 mm molded 38 x 38 concave grating?

Is the concave (meniscus) top surface suitable for the 25 mm molded 38 x 38 grating for general walkway?

How are these 25 mm molded 38 x 38 concave panels for general walkway fixed to the supports?

What panel size, MOQ and lead time apply to the 25 mm molded 38 x 38 concave grating for general walkway?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]