FRP/GRP Grating Specification · Cable Trench Cover
25 mm Molded FRP/GRP Grating, 38 x 38 mm Mesh, Concave Top for Cable Trench Cover
25 mm molded FRP/GRP grating, 38 x 38 mm mesh configured with a concave top for cable trench cover. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.
Specification
| Product type | Molded FRP/GRP grating |
|---|---|
| Mesh | 38 x 38 mm |
| Depth | 25 mm |
| Standard panel | 1220 x 3660 mm, cut to size |
| Open area | 68 % |
| Unit weight | 12.5 kg/m² |
| Recommended resin | Isophthalic polyester |
| Surface | Concave (meniscus) top |
| Bar orientation | Bidirectional molded lay-up distributes foot and light equipment loads across both bar directions. |
Allowable uniform load by support span
| Support span | Allowable UDL (kN/m²) |
|---|---|
| 600 mm | 12.5 kN/m² |
| 900 mm | 6.0 kN/m² |
| 1200 mm | 3.2 kN/m² |
Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.
Selection rationale
Laid over buried or routed cable runs in a plant room or substation, this 25 mm molded 38 x 38 cover sees light foot traffic and occasional equipment access while staying non-conductive and corrosion-resistant around the cables it guards. Where a cable route carries heavy wheeled access or spans a wide unsupported opening, this light section is not the right choice; move up to a deeper molded or pultruded profile. The low-profile 25 mm molded member suits personnel and occasional light equipment on short bearer spans. The concave meniscus crown drains water off the contact patch and grips damp footwear without added grit. Cut edges and openings are finished after the drawing and cutout positions are confirmed. Cutouts and edges are finished after layout confirmation; the walking condition governs the finish choice.
Section profile and fixing
The 25 mm molded panel suits short, lightly trafficked decks where a low-profile, lightweight bearing is enough for personnel and occasional light equipment. As a bidirectional molded lay-up, the panel can be oriented either way on the supports; clips are spaced to the frame layout, and edges are checked for even bearing.
Surface finish
The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.
Data availability
For this 25 mm molded 38 x 38 concave cable trench cover, unit weight 12.5 kg/m² and open area 68 % are verified, so these two fields do not require factory confirmation.
Resin selection
Isophthalic polyester. Isophthalic polyester covers wastewater, seawater, mild acid and moist atmospheric service within the listed temperature bound.
Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.
Installation, fixing and delivery
Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.
Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.
Request-for-quotation inputs
- Overall dimensions and required panel layout
- Support spacing / clear span and beam layout
- Design load: uniform, wheel or point load, and expected use
- Resin requirement and contact medium, concentration and temperature
- Surface finish (concave, grit or smooth)
- Quantity in square metres
- Destination country and any local standard to follow
Typical uses
- cable trench cover
- molded cable trench cover
- concave-top cable trench cover
- industrial personnel walkway
- corrosion-resistant platform deck
- open-mesh drainage and ventilation deck
