📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

FRP/GRP Grating Specification · Landscape Boardwalk

25 mm Molded FRP/GRP Grating, 38 x 38 mm Mesh, Concave Top for Landscape Boardwalk

25 mm molded FRP/GRP grating, 38 x 38 mm mesh configured with a concave top for landscape boardwalk. The verified span-load values below support an initial selection; final section and resin are confirmed against your drawing, medium and support layout.

Specification

Product typeMolded FRP/GRP grating
Mesh38 x 38 mm
Depth25 mm
Standard panel1220 x 3660 mm, cut to size
Open area68 %
Unit weight12.5 kg/m²
Recommended resinOrthophthalic polyester
SurfaceConcave (meniscus) top
Bar orientationBidirectional molded lay-up distributes foot and light equipment loads across both bar directions.

Allowable uniform load by support span

Support spanAllowable UDL (kN/m²)
600 mm12.5 kN/m²
900 mm6.0 kN/m²
1200 mm3.2 kN/m²

Values are verified allowable uniform loads for a simply supported single span at L/200 deflection. They are an initial selection aid, not a project design certification; wheel loads, point loads, cantilevers, edge cuts and concentrated equipment loads require separate engineering review. Weight and open area not present in the verified data are marked confirm_with_factory and are not estimated.

Selection rationale

This low-profile 25 mm molded 38 x 38 panel is sized for a scenic pedestrian route over gardens, ponds or promenade edges where the deck stays dry to damp and meets only atmospheric moisture or light spray, with no continuous chemical attack. It should not be read as a span for long unsupported stretches, service-vehicle crossings or concentrated machinery bases; those duties need a deeper profile. A light 25 mm molded panel for short, lightly trafficked decks where a low-profile bearing suffices. A meniscus-shaped top that sheds runoff and keeps wet-foot grip on drained outdoor routes. Panel direction, clips and edge bearing are checked to the frame drawing before fixing. The panel is laid to the section direction; upkeep follows the care guidance for the chosen top.

Section profile and fixing

The 25 mm molded panel suits short, lightly trafficked decks where a low-profile, lightweight bearing is enough for personnel and occasional light equipment. As a bidirectional molded lay-up, the panel can be oriented either way on the supports; clips are spaced to the frame layout, and edges are checked for even bearing.

Surface finish

The meniscus-shaped concave top drains water away from the contact patch and grips wet footwear without an added grit layer. General wet walkways, drainage decks and outdoor routes that remain drained under normal use.

Data availability

For this 25 mm molded 38 x 38 concave landscape boardwalk, unit weight 12.5 kg/m² and open area 68 % are verified, so these two fields do not require factory confirmation.

Resin selection

Orthophthalic polyester. Orthophthalic polyester suits fresh water, mild alkaline and dry-to-damp general service; it is not for strong acid or solvents.

Final resin is set against the contact medium, concentration and temperature; media outside the guide are confirmed in writing.

Installation, fixing and delivery

Panels are standard 1220 x 3660 mm, cut to size on request, and fixed with M/C/L/Z FRP clips or non-corrosive fasteners to the support frame; pultruded bars span between supports in the load direction. Edges and cut openings are finished by the factory after the drawing and cutout positions are confirmed.

Standard-size production runs about 15–25 days; overall delivery, including fabrication, packaging and shipping, is typically 12–36 working days by destination. MOQ is 10 m²; fabrication drawings are confirmed before production.

Request-for-quotation inputs

  • Overall dimensions and required panel layout
  • Support spacing / clear span and beam layout
  • Design load: uniform, wheel or point load, and expected use
  • Resin requirement and contact medium, concentration and temperature
  • Surface finish (concave, grit or smooth)
  • Quantity in square metres
  • Destination country and any local standard to follow

Typical uses

  • landscape boardwalk
  • molded landscape boardwalk
  • concave-top landscape boardwalk
  • industrial personnel walkway
  • corrosion-resistant platform deck
  • open-mesh drainage and ventilation deck

Technical datasheets

Related pages

Frequently asked questions

What uniform load does the 25 mm molded 38 x 38 concave grating for landscape boardwalk carry at a 900 mm span?

Which resin suits the landscape boardwalk on this 25 mm molded 38 x 38 concave grating?

Is the concave (meniscus) top surface suitable for the 25 mm molded 38 x 38 grating for landscape boardwalk?

How are these 25 mm molded 38 x 38 concave panels for landscape boardwalk fixed to the supports?

What panel size, MOQ and lead time apply to the 25 mm molded 38 x 38 concave grating for landscape boardwalk?

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]