📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
FRP Pultruded Profiles

FRP Round Rod — Pultruded Solid Bar

A solid round bar with the fibres running along the axis. Used for machined parts, pins, tie rods, and anywhere a bolted connection needs a composite insert instead of a steel one.

What it is and what it is not

Round rod is a pultruded solid cylinder, not a tube. The whole section carries load, which makes it efficient in tension and reasonably efficient in bending in any direction, because a circle has the same second moment of area about every axis through its centre.

It is not a fastener. A pultruded rod can be threaded with a die, but the thread cuts across the reinforcement and the joint is much weaker than the bar. Where a connection needs a threaded end, the standard answer is a moulded or machined stud, or a stainless bolt through a plate.

Where round rod is used

  • Tie rods and tension members in FRP frames, where the rod pulls two members together and carries the load in tension.
  • Pins, rollers and machined inserts where a steel part would corrode or where an FRP-to-FRP joint needs a non-metallic pin.
  • Handrail infill and small diameter rails on light structures.
  • Machined parts: bushes, spacers and small components turned from rod stock.
  • Anchors and dowels in concrete or timber where a corrosion-free tie is wanted.

Behaviour

In tension the rod is the best use of the material: the full section carries the load and the fibres run the right way. In bending the capacity follows diameter cubed, so doubling the diameter multiplies the stiffness by sixteen, which is why small changes in rod diameter swing capacity so far.

In compression a long rod is a column and will buckle long before it crushes. Slender FRP rods are not compression members, and a rod used to prop something should be a tube or a larger section.

Detail notes

Where the rod is used as a tie, the ends are the design. A ferrule, a plate with a hole and a bolt through it, or a swaged connection all work; a bare rod end pushed into a hole and relying on friction does not.

Cut rod with a diamond blade and seal the cut where the end will be exposed. Where the rod is machined, machining of pultruded stock is done dry or with coolant, and the machined surface should be sealed because it exposes reinforcement.

Specifying an FRP round rod

  • Diameter and length, and the tolerance that matters for the connection.
  • Grade to BS EN 13706 where the rod carries structural load.
  • Resin, and whether the rod is exposed to chemicals or UV.
  • Whether the rod is supplied plain, cut to length, or machined to a drawing.
  • Thread requirement, stated explicitly, because threading a pultruded rod is a different product from a plain rod.

Related pages

FAQ

What is FRP round rod used for?
Tie rods, pins, machined inserts, small rails and dowels. It is strongest in tension, where the whole section works.
Can FRP rod be threaded?
It can, and the thread is the weakest part of the assembly. Where a threaded connection is needed, specify a machined stud or use a bolt through a plate.
Is round rod stronger than square rod?
In bending about any axis, the circle behaves the same in every direction, which is its advantage. A square rod of the same cross-sectional area is stiffer about its axes but weaker on the diagonal.
Can FRP rod be used in compression?
Only as a short strut. A long slender rod buckles well below its compressive capacity.
What diameter rods do you supply?
Rods are pultruded to order; send the diameter, length and tolerance and we will confirm what the die can produce.
Does the cut end need sealing?
Yes where it will be exposed. Sealing keeps moisture out of the glass-resin interface at the cut face.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]