📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
GRP Stair Treads · Anti-Slip Nosing · BS 4592

GRP Stair Tread Grating

Stairs are where falls happen. A GRP tread with the right nosing stays walkable wet, in the dark, with muddy boots — and it never needs repainting. The nosing is not an accessory; it is the safety feature.

Anti-Slip NosingNo WeldingCorrosion FreeCustom Treads
Features

What a GRP Stair Tread Has to Do

Three things, and most specification arguments come from confusing them.

Carry the foot load

A point load at the centre of a tread is a different case from a uniformly distributed load. Treads are short-span elements, so this is usually easy — but a tread with no intermediate support and a wide stair is not.

Prevent slipping

This is the primary function and it comes from the surface plus the nosing, not from the panel thickness. Concave or gritted top, plus a contrasting abrasive nosing at the front edge.

Mark the edge

People miss the last step and the first step more than any other. A high-contrast nosing strip on every tread edge is the cheapest fall-prevention measure available on a stair.

Specification

Technical Specification

ParameterTypical tread specification
Panel thickness30 or 38 mm for treads; 25 mm on light internal stairs
Mesh38x38 or 40x40 standard; 19x19 for high heel risk in some specifications
Tread width (going)Usually 250 to 300 mm, cut from standard panel
Stair widthUp to the panel length, typically 1000 or 1220 mm before cutting
SurfaceConcave standard; gritted for external, wet or oily stairs
NosingAbrasive GRP nosing, contrasting colour, typically 50 to 60 mm deep
ResinIsophthalic general; vinyl ester external, coastal, chemical
StandardBS 4592 for GRP flooring and stair treads
ColourSafety yellow, green, grey, black; pigmented throughout, not painted
Comparison

GRP vs Steel vs Aluminium Treads

CriterionGRPGalvanised steelAluminium
Slip resistance when wetGood to excellent with gritted surface and nosingPoor unless gritted; grit is often worn awayPoor when wet
Corrosion outdoorsExcellentCoating fails at the nosing and the stringer interfaceGood in air, galvanic risk at steel fixings
RepaintingNeverEvery 3 to 7 years, plus nosing replacementNever
WeightLight; single-person handlingHeavyLight
Noise underfootQuietRings on open stringersRings
Thermal / electricalNon-conductive, low heat transferConductive, coldConductive, cold
Fire performanceIsophthalic burns; phenolic grade available where requiredNon-combustibleNon-combustible

The fire line is the one place GRP genuinely loses on a like-for-like basis. Where a stair is an escape route and the project requires non-combustible construction, specify phenolic GRP and confirm the fire test documentation, or use steel. Do not assume standard isophthalic grating is acceptable on an escape route.

Nosing

Anti-Slip Nosing and Custom Tread Profiles

  1. Standard abrasive nosing. A GRP nosing with embedded alumina grit, bonded or clipped to the tread front edge. Contrasting colour, usually yellow on grey. This is the default and it should be on every tread, not just the top and bottom.
  2. Nosing with a contrast strip only. Lower cost, visual marking without the extra abrasion. Appropriate for internal stairs with light traffic.
  3. Wrap-around nosing. Returns down the riser edge as well, which protects the tread edge from impact and gives a clean visual line.
  4. Custom tread profiles. Where the stringer geometry is unusual, or where a tread must integrate with an existing steel stair, the tread can be cut and edged to match rather than forcing the stair to change.

A stair without nosing is a stair with an unfinished safety design, regardless of how good the panel surface is.

Selection

Thickness and Load Selection

A tread is a short-span element fixed at both stringers. That makes the load case simple, and the usual mistake is over-specifying the panel while under-specifying the fixing.

  • Internal light stair, 1000 mm width: 30 mm tread is normally adequate.
  • External industrial stair: 38 mm, with gritted surface and nosing.
  • Wide stair or treads without a central stringer: check the point load at mid-span; a central support or a thicker tread may be needed.
  • Heavy boots and site traffic: 38 mm and a wrap-around nosing, because impact at the tread edge is the real load.

The governing consideration for most treads is not strength but stiffness under a single foot at the centre of the tread. If a tread visibly flexes when stepped on, people distrust the whole stair.

Installation

Installation Guide

  1. Check stringer spacing. Treads are cut to the clear span plus bearing. Inconsistent spacing between flights is common on older stairs and will show as uneven treads.
  2. Fix each tread with two fixings, one at each stringer, using stainless A4 outdoors. A tread fixed at one end only will rotate under load.
  3. Fit the nosing before the tread is walked on, not afterwards.
  4. Seal every cut edge with resin — treads are cut from panels, so every tread has two or four new edges.
  5. Check the step line visually along the flight. A single tread sitting a few millimetres high is the trip point people find first.
  6. Handrail and edge protection where the stair has an open side; GRP handrail keeps the system consistent.
Related

Related GRP Pages

GRP Grating — Full Range

Moulded and pultruded, resin options, standards by market.

GRP Grating Manufacturer

Who makes it, from which mould, and what a factory audit pack contains.

GRP Grating Panels

Sizes, thicknesses, weight per square metre and load data.

GRP Grating Supplier

Supply terms, lead time by route, MOQ and Incoterms.

GRP Grating Suppliers

Twelve checks before you order, and the red-flag list.

GRP Platform Grating

Industrial platform decks and access structures.

GRP Channel Grating

Trench, duct and drainage covers to BS 4592.

GRP Catwalk

Elevated walkways, pipe rack access and long access routes.

GRP Structural Profiles

I, U, angle, tube and rod to BS EN 13706.

FAQ

GRP Stair Tread FAQ

What thickness should GRP stair treads be?

30 mm for light internal stairs at typical widths, 38 mm for external and industrial stairs. The check is stiffness under a single foot at mid-span, not ultimate strength.

Do stair treads need a nosing?

Yes, in any specification concerned with fall prevention. The nosing provides abrasion at the front edge — where feet actually land — and a high-contrast strip that marks the step edge. It should be on every tread.

Is GRP suitable for fire escape stairs?

Only in a phenolic grade with the correct fire test documentation, and only where the project accepts a composite escape route. Standard isophthalic GRP is combustible and is not appropriate for a protected escape route.

Can GRP treads replace steel treads on an existing stair?

Usually yes, because GRP is lighter and the stringers are generally adequate. Check the stringer spacing and confirm the tread bearing detail — older stairs often have inconsistent spacing between flights.

How do I fix a GRP tread?

Two fixings, one at each stringer, stainless A4 outdoors. A tread fixed at only one end will rotate under load and is a defect even if it appears stable at first.

Are GRP treads slippery?

The standard concave surface is acceptable for dry internal stairs. Gritted surface plus nosing is the specification for external, wet, oily or muddy conditions.

Can treads be supplied in safety colours?

Yes. Pigmented throughout the panel, not painted, so the colour does not wear off at the tread edge. Safety yellow with a contrasting nosing is the common combination.

Do GRP treads corrode?

No. That is the main reason they replace galvanised steel on external and coastal stairs, where the coating fails first at the nosing and at the stringer interface.

Can I cut treads from standard panels?

Yes, and that is how most treads are made. Every cut edge must be sealed with resin. Buying factory-cut and factory-sealed treads avoids the most common site defect.

What is the lead time for custom treads?

Standard sizes cut from stock are short lead time. Custom profiles and colour-matched nosings involve a production run, so allow longer — confirm the date before the stair is scheduled for installation.

Next Step

Request a Stair Tread Quote

Send the stair width, going, stringer spacing, the environment and whether a nosing is required. You will get a tread schedule with nosing and fixings.

Request Quote → See Price Drivers

NANTONG ZEALL NEW MATERIALS CO., LTD. · GRP Grating Manufacturer · ISO 9001 certified

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]