📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
FRP Pultruded Profiles

FRP Flat Bar & FRP Flat Strip — Pultruded Rectangular Section

A solid rectangular strip, used where a thin flat member has to carry load or close a gap: bearing plates, edge strips, shims, ladder rungs and the flat sections a fixing detail always seems to need.

What it is

A flat bar is a pultruded rectangle with the fibres running along its length. It is not a plate: a plate is wide and thin in both directions, a flat bar is narrow enough to behave as a bar and is normally used where the depth is the dimension doing the work.

The section is simple, which is why it is useful. There is no flange to crush and no web to drill through a thin wall; a flat bar can be bolted from either face, cut with a saw, and stacked to build up a thickness where a detail needs one.

Where it is used

  • Bearing and bearing plates where a panel or a post lands on a member and the load needs spreading.
  • Edge strips and closures along a deck edge where a full angle is too much section.
  • Ladder rungs and light step treads on FRP ladders.
  • Shims and packers at connections, where a millimetre of adjustment is needed and steel would corrode.
  • Frames for small enclosures, screens and guards where the member is light and the load is nominal.

How it behaves

Bending about the strong axis of a flat bar is straightforward: the section modulus is width times depth squared over six, and the second moment of area is width times depth cubed over twelve. Rotate the bar ninety degrees and those numbers collapse, which is the whole reason a flat bar is specified with its orientation on the drawing.

A flat bar is also the easiest pultruded section to overload in bearing. A bolt bearing on a thin strip concentrates stress in a small area, and the failure shows as a crushed hole rather than a broken member. Where a connection needs bearing capacity, the bar is thicker or a plate is used.

Detail notes

Cut flat bar with a diamond blade and, where the cut face will be exposed outdoors, seal or paint it: the cut end exposes glass that would otherwise stay inside the resin.

Where a flat bar is used as an edge strip, the strip is usually bolted down through the deck and the bolts land in the same line as the clips, so the take-off has to list both together or the site runs short of one of them.

Specifying an FRP flat bar

  • Width and thickness, stated separately, and the orientation on the drawing.
  • Grade to BS EN 13706 where the bar carries load; grade is often waived for pure trim.
  • Resin: isophthalic polyester standard, vinyl ester for chemical service.
  • Length, cut list, and whether the ends need sealing.
  • Surface finish and colour, and whether the bar is part of a visible edge where colour match matters.

Related pages

FAQ

What is the difference between FRP flat bar and FRP plate?
A flat bar is a narrow rectangular section used as a bar; a plate is a wide sheet used as a surface. Both are pultruded, and both are usually specified by width and thickness.
Can flat bar be used as a beam?
Over short spans and light loads, with the depth vertical. Rotated onto its side, its capacity falls away sharply.
How thick does a bearing plate need to be?
Enough that the bolt bearing stress stays within the material and the hole does not crush. If in doubt, use a plate rather than a thin bar.
Do cut ends need sealing?
Where the end is exposed outdoors or in a chemical environment, yes. Sealing keeps water out of the glass-resin interface at the cut.
What grade of flat bar do you supply?
E17 or E23 to BS EN 13706 where the section is structural; the grade can be waived for trim that carries no load.
Can flat bar be supplied in a colour matched to the grating?
Yes. Colour is set from a reference sample and matched across the order, which matters where the bar sits at a visible edge.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]