📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
Industry solution — Agriculture & livestock housing

FRP Grating for Agriculture and Livestock Housing: Walkways and Slatted Floors

Livestock housing is quietly one of the most corrosive places you can walk: ammonia and hydrogen sulfide rising from manure, daily high-pressure washing with disinfectant, feed acids and fats, hoof traffic and heavy point loads from sows, cattle and loaded carts. Ordinary steel grating rusts and flakes within a couple of seasons, the bars trap manure, and the floor becomes slippery and unsanitary. This page explains why steel is eliminated in barns, how molded and pultruded FRP (fiberglass reinforced polymer) is selected for walkways, slatted floors and covers, and what must be confirmed for your housing type before an order is cut.

We are a grating factory, not a farm or a veterinary supplier. The conditions below come from public agricultural-engineering references and normal commercial supply practice; we hold no on-site measured data from a specific barn. Use the figures as a starting point, and let our engineering team confirm them against your layout.

Values on this page are typical ranges from public industry references and normal commercial supply. We do not operate farms and hold no on-site measured data for livestock buildings — final figures are confirmed against your actual housing conditions and our factory engineering team, and fixed on the approved order drawing.

Why steel floors and walkways fail in a barn

A painted or galvanized steel floor in a pig or dairy house looks robust, but it is exposed to the worst combination of agriculture: ammonia attacks the coating and continues underneath, manure and urine form a dilute but aggressive electrolyte, and weekly disinfection with phenolic, quaternary-ammonium or hypochlorite compounds strips whatever protection is left. Within two to four years the bearing bars are corroded in section, the edges are rough, and the surface holds manure instead of shedding it.

Beyond corrosion, steel is the wrong material for a wet, hoof-traffic floor: it is cold, hard and slippery when wet, it conducts, and it needs welding for any alteration. A glass-fiber composite does not eat ammonia, does not flake, is light to lift for cleaning, and can be cut to opening widths that match the animal's hoof. That is the honest reason barns are switching away from ordinary steel grating.

The real working conditions inside a livestock building

Selecting a resin or bar width starts by naming the exposure, because a breeding room and a slaughter-route corridor are different environments. In a working barn the walking and standing surface sees several of the following at once.

Ammonia and hydrogen sulfide build up where manure sits under slats; they are corrosive to metal and irritating to animals and staff. High-pressure washing floods the aisle several times a week, so the surface is alternately soaked and dried. Disinfectants run on phenols, quaternary ammonium compounds and sodium hypochlorite at working dilution, dosed after each wash. Feed acids, milk residues and fats coat the feeding and drinking areas. Loads are concentrated: sows and dairy cows stand and turn, weaner pigs rush down alleys, loaded feed carts and the occasional weighbridge or hoof-trimming point put a heavy wheel or foot load on a small area.

Dairy houses add a hygiene and hoof-health demand: the floor must drain and not become a standing puddle, because wet hoof tissue is where lameness starts. Poultry houses use narrow slatted strips that keep birds out of the manure pit below. Silage clamps and covered channels add acidic silage juice and UV exposure.

  • Ammonia and hydrogen sulfide from accumulated manure.
  • Frequent high-pressure wash-down flooding the aisles.
  • Phenolic, quaternary-ammonium and hypochlorite disinfectants.
  • Feed acids, milk residues and fats around feeding points.
  • Concentrated hoof and foot loads, carts and occasional weighbridge use.
  • Dairy drainage and hoof-hygiene requirement; poultry slatted strips.
  • Silage juice acidity and outdoor UV on covered clamps.

Where grating, slats and plates go in a building

A barn uses three different forms, chosen by what has to fall through and what has to carry a standing animal. The standing and walking surface is open grating or slats; the covers over pits, channels and silage clamps are solid; and the edge framing and supports are pultruded profiles. In many export markets the same composite is called GRP grating rather than FRP; it is one and the same glass-reinforced plastic.

Walkways and breeding aisles use open molded or pultruded grating so that wash-down water and manure pass through. Slatted floors use narrow, spaced strips whose gap is set by the species and hoof size — the gap must let manure through without catching a claw or hoof. Covers over manure channels, sumps and silage pits are solid plate or molded covers that keep staff and equipment out of the waste below. Handrails, gates frames and support beams are pultruded profiles that can be cut and assembled without welding in the ammonia atmosphere.

  • Walkways, breeding and service aisles: open molded grating, grit-topped.
  • Slatted floors: spaced pultruded or molded strips, gap per species.
  • Manure-channel and trench covers: solid FRP plate, or a GRP trench cover over the scraping channel.
  • Gate frames, handrails and supports: pultruded GRP profiles, no welding in the ammonia air.
  • Drinking and washing zones: open, draining, anti-slip surfaces.

Selection logic: molded panel, pultruded slat, plate

Molded (molded-in-the-square) grating is the default aisle walkway. It is a tough interwoven grid, cuts on site, and sheds manure better than a solid plate because openings let waste drop through. The common 38 mm panel is the working standard for foot and light-cart traffic; deeper sections are specified where a loaded feed cart or a heavier span runs.

Pultruded slats and profiles are used for the slatted floor itself and for any straight beam: continuous glass along the span gives a stiff, predictable strip whose gap can be set to the hoof. The slit width is chosen by species and hoof/claw shape — pig weaners, finishing pigs, dairy cows and poultry all need different openings — and must be confirmed per housing type rather than taken from a catalogue. Solid FRP plate closes pits, channels and splash zones where nothing should fall through.

The resin follows the disinfectant. Isophthalic polyester suits mild, clean wet service. Where hypochlorite, phenolic or quaternary-ammonium disinfectants are dosed at working concentration on a regular schedule, vinyl ester is the grade we start from, because it holds up to oxidizing cleaners better than standard polyester. Wet dairy and washing zones get a bonded quartz-grit anti-slip face. Ordinary carbon-steel grating is not a substitute here: ammonia and manure attack it fast, and it cannot be recommended as an equal alternative.

Working-condition and material-selection table

The table maps common livestock zones to exposure, a typical temperature band, the realistic load, the resin we start from, and the structural form. Slit widths are noted as 'confirm by species' because a universal number would be wrong.

Zone in buildingMedium / exposureTypical temp.LoadResin to startStructural form
Breeding / service aisleAmmonia + weekly disinfectant15–25 °CStaff, sows, cartsVinyl esterMolded 38 mm, grit-topped
Pig slatted floorManure + H2S + wash-down15–28 °CHoof, grouped pigsVinyl esterPultruded slats, gap per species
Dairy walkwayWet, milk residue, hoof traffic5–25 °CCows, drainage neededVinyl esterMolded 38–50 mm, grit-topped
Poultry slatted stripManure + ammonia, dry-ish18–28 °CBirds, lightIsophthalicNarrow pultruded strips
Manure channel / sump coverEffluent, gases, disinfectant5–30 °CFoot, occasional cartVinyl esterSolid plate or molded cover
Silage clamp coverAcidic silage juice + UV-10 to 35 °CFoot, equipmentVinyl ester, UV-stabilisedSolid plate / cover
Gate frame & handrailAmmonia atmosphere + wash5–30 °CPoint loads, structuralVinyl esterPultruded profiles

Typical bands only. Slit width is confirmed by species and hoof/claw shape; span and deflection are set from your actual bay width and cart load. We do not recommend plain steel grating in ammonia-and-manure service.

Drainage, slit width and anti-slip surfaces

A barn floor is supposed to pass wash-down water and manure while keeping the animal's hoof on top. The open area and the slit width set that balance: too open and claws, toes or cart wheels catch; too closed and water and manure pool, which is exactly where hoof disease and slips start. For dairy in particular, a draining, non-puddling surface is a welfare and lameness decision, not only a corrosion one.

Slip resistance comes from the bar profile plus a bonded quartz grit on the walking face. In washing bays, dairy alleys and any permanently wet zone we default to the grit-topped surface, because a wet composite is slippery even when it looks dry. The grit is moulded into the resin layer, so it wears with the panel rather than peeling like a coating.

Fixing, clips and what not to bolt in

The fixing is where a 'corrosion-free' floor quietly becomes a maintenance item. Do not bolt a composite slat into a plain steel frame in an ammonia atmosphere — you have reintroduced the corrosion you removed. Use composite grating clips or 316 stainless hardware seated on the composite, and keep dissimilar metals apart in the wet, washed zone.

Panels and slats should be clamped to allow small thermal movement, not welded. Frames and supports in the wash zone are pultruded for the same reason the slats are: a non-conductive, ammonia-proof system holds together where a welded steel frame would rust at every weld toe.

Project references and a detailed flooring guide

We do not supply livestock barns under the named cases below, and we will not suggest otherwise. These references show the same exposure family that barn flooring lives in — effluent, disinfectants, wet walkways and covers — and are evidence of how the material behaves in corrosive, washed-down, walked-on service.

For the finer points of choosing slatted flooring in animal housing, we have a dedicated technical article. This industry page is a solution overview; the flooring article is where the slat and gap detail lives. We deliberately keep that article as the home of the slatted-flooring subject so that the two pages do not compete.

The named projects are not farms; read them for material and fixing behaviour. The livestock flooring article is the detailed home of that subject — this page links to it rather than repeating it.

What we confirm before we quote — and what we do not claim

To turn this page into a buildable order we need a short technical pack: the species and housing type, bay widths and spans, the design load (animal weight, cart or weighbridge wheel load), the disinfectants you use and their working dilution, and the climate band. From that we return a panel or slat depth, a slit-width recommendation to confirm, a resin choice and a clip schedule.

Our factory has produced composite grating since 2004, runs on about 20,000 m², employs 200+ people and exports to 40+ countries. Typical lead time is 12 to 36 working days depending on panel mix and cut lengths. Oversized panels, custom colours, new moulds and specialty resins are quoted with a separately confirmed schedule. We hold ISO 9001 (GB/T 19001-2000 idt ISO 9001:2000, certificate 01708Q11888R0S) and an ASTM F3059 report (211122012SHF-001) for grating specifically. We do not hold ABS or SGS product certification and we will not describe one as if we did. We also hold no livestock-building field data, and we will not invent a farm number.

  • Send species, spans, wheel loads, disinfectants and climate band.
  • We return panel/slat depth, slit width to confirm, resin and clips.
  • Lead time typically 12–36 working days; trial panels accepted.
  • ISO 9001 and ASTM F3059 (grating) held; ABS/SGS not claimed.

Agriculture and livestock grating — frequently asked questions

Why not just use steel grating in a pig or dairy house?

Ordinary steel rusts and flakes quickly under ammonia, manure and weekly disinfection, traps manure on rough bars, and stays cold and slippery when wet. A composite floor does not attack ammonia, sheds water and manure through its openings, and can be cut to a hoof-safe slit width. We still calculate the panel depth and span — composite is not stiffer than steel — but in ammonia-and-manure service it outlasts plain steel by a wide margin.

Which resin stands up to barn disinfectants?

For phenolic, quaternary-ammonium and hypochlorite disinfectants dosed at working dilution on a regular schedule, we start from vinyl ester rather than standard polyester. Send the actual disinfectant and dilution; isophthalic polyester can still suit mild, clean wet service.

How wide should the slatted floor gap be?

The slit width is set by species and hoof/claw shape — weaners, finishing pigs, dairy cows and poultry all need different openings — so it must be confirmed per housing type rather than taken from a catalogue. The gap lets manure through without catching a claw or toe.

Can FRP flooring handle a dairy cow and hoof traffic?

With a properly sized panel depth and span, a grit-topped molded panel gives a draining, non-slip walking surface that helps keep hooves dry, which is a lameness and welfare concern. The exact depth comes from the span and the expected load, not from the animal weight alone.

How are the panels fixed without corroding the frame?

Use composite clips or 316 stainless hardware seated on the composite, never plain carbon or galvanized steel in the washed zone, and keep dissimilar metals apart. Clamp for small thermal movement rather than welding; supports and gate frames are pultruded for the same ammonia-proof reason.

Do you have measured data from a real barn?

No. We are a grating factory and hold no on-site measured data from livestock buildings. The figures on this page are typical industry values from public references; your species, spans, loads and disinfectants are confirmed by our engineering team and fixed on the approved drawing.

Related pages

Send the barn conditions, not a catalogue number

Give us the species and housing type, bay widths, wheel or animal loads, the disinfectants you use and their dilution. We come back with panel or slat depth, a slit width to confirm, resin and clips, plus a lead time.

Request a quote →

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]