GRP Wound Pipe
FRP/GRP filament-wound pipes and tubes for chemical, wastewater, drainage and ventilation lines; hoop-reinforced, corrosion-proof and produced to diameter and pressure rating.
FRP/GRP filament-wound pipes and tubes for chemical, wastewater, drainage and ventilation lines; hoop-reinforced, corrosion-proof and produced to diameter and pressure rating.
{p["overview_title"]}
Hoop reinforcement
Filament winding lays down circumferential reinforcement that resists internal pressure and ring loads better than straight pultrusion alone.
Corrosion-proof lines
Composite pipe resists acids, alkalis, brine and H₂S that corrode steel or concrete pipe in chemical and wastewater service.
Sizes and joints
Tubes are wound to diameter and length, joined with composite couplers, flanges or bonded sockets per the line design.
Wound Pipe Specifications
Wound pipes carry fluid pressure and ring loads in corrosive service. Typical diameter, wall and resin options are below.
| Parameter | Standard Range | Notes |
|---|---|---|
| Diameter | 50 – 600 mm | Made to drawing |
| Wall thickness | 3 – 20 mm | Hoop + axial plies |
| Pressure | per design rating | Per medium/head |
| Resin | Polyester / Vinyl ester / Epoxy | Vinyl ester for chemicals |
| Joint | Coupler / flange / socket | Per line detail |
| Finish | Smooth inner/outer | Resistant liner |
Supplied with COA and load/property test reports; send your dimensions and load for a matched specification.
Composite Wound Pipe vs Steel vs PVC Pipe
Pipework faces corrosion, pressure and chemical attack. The table compares wound composite pipe with steel and PVC on the deciding properties.
| Property | FRP/GRP Wound Pipe | Steel Pipe | PVC Pipe |
|---|---|---|---|
| Corrosion | Resists acids, brine, H₂S | Rusts; liner needed | Resistant |
| Pressure | High hoop strength | High | Moderate |
| Weight | Light | Heavy | Light |
| Temperature | Resin-dependent | High | Limited |
Wound members complement pullwound profiles and pultruded sections.
Where Wound Composite Pipe Is Used
Chemical process: Corrosion-resistant wound lines route acids, alkalis and process fluids through units.
Wastewater & drainage: Composite pipes resist H₂S, brine and wash-down in treatment and drainage networks.
Ventilation & cooling: Wound ducts carry exhaust air and cooling water in industrial and marine service.
Wound Pipe Selection
- State medium, concentration, pressure/head, diameter and temperature.
- Select resin system and liner suited to the chemical exposure.
- Confirm joint type, length and support spacing; supply cut-to-line pipes and fittings.
See the installation guide and grating clips for fixing.
Related Products and Guides
- FRP Pullwinding Profiles — hybrid wound sections
- FRP Pultruded Profiles — axial sections
- FRP Structural Profiles — framing
- FRP Platform Grating — pipe-rack decks
Request Your GRP Wound Pipe Quote
Email [email protected] · Tel/WhatsApp +86-513-6681-9918 · Nantong, Jiangsu, China
GRP Wound Pipe FAQ
Product and factory gallery






Technical Documentation (PDF)
Download the FRP/GRP technical documents relevant to this page. Figures are indicative — confirm against a stamped project calculation.
- frp-grp-grating-technical-data-sheet.pdf (5 KB, PDF)
- frp-grating-load-table.pdf (4 KB, PDF)
- installation-maintenance-manual.pdf (81 KB, PDF)
- installation-node-details.pdf (81 KB, PDF)
Download Document
Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!
Thank You!
Your request has been received successfully.
Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!
If you need urgent assistance, please email: [email protected]
