📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
FRP Grating Specifications

50 mm T-Bar Pultruded FRP Grating

A deep T-bar section for three to four metre spans, used where a long clear opening must be crossed without added steelwork.

Technical specifications

TypePultruded FRP grating, T-bar section, deep bar
Bearing bar depth50 mm (2 in)
Top flange width15 mm
Bar pitch38 mm standard; 50 mm pitch for open-area critical layouts
Open areaabout 40% (clear 15 mm) or about 50% (clear 19 mm)
Unit weightabout 17 kg/m² at 40% open; about 15 kg/m² at 50% open
Standard panel1220 x 3660 mm, cut to size; longer panels on request
Resin systemsIsophthalic polyester; vinyl ester; phenolic for fire-critical and offshore work
SurfaceConcave or grit; smooth available for wash-down decks
FixingHeavy-duty saddle and clip with SS316 bolts; end fixings at every bearer

Load and span guidance

Support spanIndicative UDL, 40% openIndicative UDL, 50% openDeflection basis
2.5 mabout 620 kg/m²about 540 kg/m²L/200
3.0 mabout 420 kg/m²about 365 kg/m²L/200
3.5 mabout 300 kg/m²about 260 kg/m²L/200
4.0 mabout 220 kg/m²about 190 kg/m²L/200

Indicative only, for a simply supported single span under uniform load. Long-span pultruded decks are normally governed by deflection, so the deflection limit rather than the material strength decides the section. Confirm the allowable load against our certified table before release for construction.

When depth beats extra steel

Every additional bearer under a walkway costs steel, fabrication, coating and a crane lift. A 50 mm section removes one or two bearer rows from a typical three to four metre platform, and the extra 4 kg/m² of grating is usually far cheaper than the frame it replaces. This is the economic argument for the deep bar, and it is the one that wins most often in retrofit work where the existing frame cannot be extended.

The deep T-section is also the practical answer for vibration and walking comfort. Deflection under a walking person falls roughly with the cube of the depth, so the deck feels solid rather than springy, and the panel is less prone to the edge abrasion that appears where a light deck flexes against a fixed handrail post. Where the client specifies L/300 or a 150 kg point load at mid-span, the 50 mm depth usually satisfies both without a change of resin.

Where it fits

  • Long-span process platforms and pipe rack access
  • Rooftop and cooling tower walkways with limited support points
  • Offshore and marine decks with vinyl ester or phenolic resin
  • Tank farm and terminal platforms crossing pipe trenches
  • Heavy-duty stair landings and stringer-connected treads

Deep panels are heavy enough that two people should lift them with a spreader rather than by the bar ends. Bearers must be level within about 3 mm over the panel length, because a deep bar is less forgiving of a twisted frame than a 25 mm section.

Related resources

FAQ

W
T
I
A
D
T
C
Y
W
P
H
E

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]