📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
FRP Grating Specifications

38 mm T-Bar Pultruded FRP Grating

The workhorse pultruded section: 38 mm bearing bar depth for platform spans of two to three metres without intermediate support.

Technical specifications

TypePultruded FRP grating, T-bar section
Bearing bar depth38 mm (1.5 in)
Top flange width15 mm
Bar pitch38 mm (1.5 in) standard; 25 mm pitch for heavier duty
Open areaabout 40% (clear 15 mm) or about 50% (clear 19 mm)
Unit weightabout 13 kg/m² at 40% open; about 11.5 kg/m² at 50% open
Standard panel1220 x 3660 mm (4 x 12 ft), cut to size
Resin systemsIsophthalic polyester; vinyl ester for chemical and marine service; phenolic where fire performance is specified
SurfaceConcave standard; grit for ramps and wet decks; smooth for clean rooms
FixingClip system with SS304 or SS316 bolts; no drilling, no welding

Load and span guidance

Support spanIndicative UDL, 40% openIndicative UDL, 50% openDeflection basis
2.0 mabout 520 kg/m²about 450 kg/m²L/200
2.5 mabout 330 kg/m²about 285 kg/m²L/200
3.0 mabout 220 kg/m²about 190 kg/m²L/200
3.5 mabout 150 kg/m²about 130 kg/m²L/200

Indicative values for a simply supported single span with uniform load. The governing allowable load is taken from our certified table for the specific section, resin and deflection limit. For spans above 3 m a 50 mm depth is usually more economical than propping the 38 mm panel.

Why 38 mm is the default section

Thirty-eight millimetres is the depth at which pultruded grating starts to behave like a structural deck rather than a walking surface. At 11.5 to 13 kg/m² it reaches spans of roughly three metres at foot-traffic loads, which covers most mezzanine, roof access and process platform layouts without an intermediate bearer. Use of that one extra 13 mm of depth removes a whole row of secondary steel from the design.

It also tolerates the operating realities of a plant: a maintenance trolley, a drum dropped on the deck, a forklift nudging the edge. The 15 mm top flange spreads a point load across two bars, and because the bar depth is greater the panel deflects less for the same load. In chemical plants we pair it with vinyl ester resin so that both the section and the resin are graded for the environment, rather than upgrading only one of the two.

Where it fits

  • Process and utility platforms in chemical, pharma and food plants
  • Roof access walkways and rooftop plant decks
  • Pump and compressor platforms in water and wastewater works
  • Marine and offshore walkways, with vinyl ester resin
  • Ramps and sloped access where grit surface is specified

Panels are laid with the bearing bars spanning between bearers, never cantilevered more than about 150 mm past a support. Where panels meet, a clip is placed at the shared bearer and the joint is kept in line with the bearer centre line.

Related resources

FAQ

W
A
H
T
W
I
H
A
C
I
I
A

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to [email protected]. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: [email protected]